Responsive image

Academic Research - Mechanical Engineering


Research Facilities

Sl. No.FacilityDescription
1IC Engine Test Rig with eddy current dynamometerA single cylinder four stroke diesel engine fitted with eddy current dynamometer for performance analysis. Computerized monitoring of combustion characteristics for different blending of diesel and bio diesel may be carried out.
2AVL DIGAS AnalyserIt consists of sensors for sensing Co, Co2, O2,NOx and smoke of exhaust gas from IC engines
(both petrol and diesel). It consists of inbuilt data storage and printer facility.
3Vibration AnalyzerThe system consists of ADASH 4300 Vibration analyzer (frequency range: 0.8 Hz-20000 HZ), Accelerometer (100mv/g), Vibrating table (0-1000Hz) and impulse force hammer (0-2000N). It finds application in diagnostics of mechanical defects (unbalance, misalignment, looseness, physical damage etc.,) of rotating elements viz bearings and shafts of pumps, turbines etc.
4Electronic TensometerIt is a tensile testing machine consisting of DC Servomotor, Microprocessor based controller for elongation measurement with a quick grip chuck; wire size from 1mm to 8 mm diameter and strips from 1mm to 5mm thickness and a maximum width of 19 mm. Test specimen length is 135 mm. The maximum permissible load is 20 kN Specimens like polymer composites, aluminum rods and plates, copper rods and plates etc., may be tested.
5Metallurgical Microscope with high resolution cameraThis is a metallurgical device used for the analysis of microstructure of engineering materials.
It consists of USB digital camera with 400X magnification and 1024 pixel resolution.
6Micro Vicker Hardness TesterIt is a mechanical type hardness tester to find the hardness of materials such as composites.
The applied load may vary from 10 mg to 200 grams.
7Stir Casting furnaceIt is a device used for melting and casting of powder materials in powder metallurgical analysis.
The maximum melting temperature is 1350 degree Celsius with an inbuilt temperature sensor
8Coordinate Measuring MachineIt is a bridge type semi automatic 3D CMM with stylish probe and control panel with application software. The maximum traverse in X,Y, and Z coordinates are 460 mm, 500 mm, and 420 mm respectively. Accuracy of measurement is +/-0.001 mm
9Force plate with Bioware softwareIt is a device consisting of series of piezoelectric crystals, used for the ergonomic analysis (Forces Fx,Fy,Fz, and Moments Mx,My,Mz) of static and dynamic work posture in carrying out a repetitive / forceful / awkward job by workers. This helps in identifying a comfortable work posture and in enhancing safety while carrying out a job. It finds applications in man power intensive industries. Design optimization of workstation /workbench on which the work is carried out by workers may also be carried out.
10Abrasive CutterAbrasive Cutter features manual cutting action with best in class lighting, visibility and cut capacity. With its large workspace and versatile vising options, this cutter enables simple, quick and easy positioning of samples for cutting and sectioning
11Specimen Mounting PressCompression Mounting System that delivers speed and intelligence to the compression mounting process.
12Auto Polishing MachineThe goal of any method is to prepare a final polished specimen free of deformation and suitable for analysis. The initial abrasive size should be as small as possible, yet be able to create a flat surface and remove any sectioning deformation. Each subsequent step should induce as little deformation as possible while removing any damage from the previous step. Using adequate lubrication, most commonly water, throughout the process will aid in minimizing deformation.
13Inverted MicroscopeMicroscopes for material analysis must use reflected light. Whether upright or inverted, either can be paired with image capture and analysis systems, including cameras and analysis software. Common applications like grain size, porosity and phase percentage have now been incorporated into ready made routines.
14Microhardness TesterMicrohardness testing, commonly referred to as Knoop and/or Micro-Vickers testing, is performed by pressing an indentor of a specified geometry into the test surface. Applying only a single test force, the resultant impression or unrecovered area is measured. The Knoop diamond produces an elongated rhombic based diamond shaped indent with a ratio between long and short diagonals of about 7 to 1. Knoop tests are typically performed at test forces from 10 - 1000g, are best used in small test areas or on brittle materials as minimal material deformation occurs on the short diagonal area.
15Probe Sonicator Sonication is the act of applying sound energy to agitate particles in a sample, for various purposes. Ultrasonic frequencies are usually used, leading to the process also being known as ultrasonication or ultra-sonication
16Muffle Furnace A furnace with an externally heated chamber, the walls of which radiantly heat the contents of the chamber.Heating Element of the furnace is Kanthal A1 Coiled coil type wound and placed inside a grooved element holding brick with lead out taken out in a junction box to connect the attached control panel.
17Surface roughness testing machineThe surface roughness testing machine is a shop floor type surface roughness and waviness measuring instruments which, traces the surface of various machine parts, calculates their surface roughness based on roughness standards, and displays the result.
18Gas analyser compact model AVL 444 (5 Gas)Gas analyser compact model AVL 444 (5 Gas) to measure the exhaust smoke values (CO, CO2, HC, O2, NO and Lambda calculation) from all petrol, CNG, LPG and diesel driven vehicles engines.
19Flue gas analyserFlue gas analyser is used to analyse the flue gases from boilers and biomass gasifiers. CO, CO2, CxHg and SO2 flue gas temperature can be measured.
20Thermal ImagerI is used as a preventive maintenance tool. Heat dissipated from electrical utilities and thermal utilities can be studied with temperature distribution obtained by scanning thermal imaging camera.
21IR ThermometerIt is used to measure the surface temperature
22Grain Moisture MeterIt is used to find the moisture content in wood chips, vice husk and fire wood etc
23Hot wire anemometerIt is used to measure the mass flow rate of flue gas
24Indoor air quality metermeasure humidity and CO2 level in the room
25pH meterMeasure pH of liquids
26Solar PV TestingTo test the photovoltaic panels under indoor conditions
27Solar thermal testingTo test the flat plate water heater under indoor conditions
28Wind electric test kitDemonstrate working of wind electric generator by artificially blowing the air using fan
29Solar parabolic trough collector testing kitBy varying the flow rates of heat transfer fluid, the hot water generation rate can be assessed with the kit.
30Computer aided refrigeration test rigRefrigeration system performance is analysed by using computer which is interfaced with data logging system
31Computer aided air conditioning test rigPerformance of air conditioning system is evaluated and analysed by using computer which is interfaced with data logging system for different climatic conditions


Supervisors

Sl. No.Name of the SupervisorReference No.Name of the UniversityResearch AreaE-Mail ID Phone No.
1Dr.V.Balusamy9920045AU, ChennaiMetallurgy Engineering and MechanicalEngineeringprincipal@kongu.ac.in9942820583
2Dr.P.Senthilvelmurugan2920067AU, ChennaiManufacturing Systems, Piping Design, Operations Management, Industrial Engineeringsenthilmangai@kongu.ac.in9443454572
3Dr.R.Rajasekar2020343AU, ChennaiMaterials Science and Engineeringrajamech@kongu.ac.in9952460698
4Dr.V.Hariharan2720042AU, ChennaiCondition Monitoring, Vibration Analysis, Bearing Fault Analysishariharan@kongu.ac.in9443504469
5Dr.P.Somasundaram2320468AU, ChennaiThermal, Refrigeration, Ic Engines, Solar somasundaram.auto@kongu.ac.in9842136616
6Dr.K.Dineshkumar2920005AU, ChennaiTribology, FEM, Metal Forming, Materialsdinesh.mech@kongu.ac.in9443599356
7Dr.S.Selvakumar2320420AU, ChennaiOptimization, Fixture Design, Neural Networks, Genetic Algorithmsskmech@kongu.ac.in9842960609
8Dr.A.Sivakumar2720041AU, ChennaiIndustrial Engineering, Optimization of Productivity and Quality, Multivariate Analysis, SCMaskmech@kongu.ac.in9865882583
9Dr.P.Thangavel2720025AU, ChennaiThermal Engineering, Refrigeration Systems, Energy Conservation, Heat Transfer Analysisptvel@kongu.ac.in9865451854
10Dr.P.Selvakumar2820082AU, ChennaiHeat Transfer, Renewable Energy, Thermal Engineeringselvakumar@kongu.ac.in9566341992
11Dr.T.P.Sathishkumar2420483AU, ChennaiNatural Fiber Reinforced Compositestpsathish@kongu.ac.in9943570495
12Dr.M.Sambathkumar3820003AU, ChennaiComposite Materials, Tribology, Machining, Corrosionsambathkumar@kongu.ac.in9952306585
13Dr.A.Mohan Kumar3920004AU, ChennaiComposite materials, Machining of composite materials, Drilling, Optimizationmohankumar@kongu.ac.in9442710605
14Dr.M.Bhuvanesh Kumar3520045AU, ChennaiIndustrial Engineering, Manufacturing Engineering, Lean Manufacturing, Material Sciencebhuvanesh@kongu.ac.in9894711713
15Dr.R.Naveenkumar3320074AU, ChennaiErgonomics, Design, CAD/CAMnaveenmech@kongu.ac.in9790267674
16Dr.S.M.Senthil3820007AU, ChennaiDesign, Manufacturing, Optimization, Materialssmsmech@kongu.ac.in9715541194
17Dr.C.Moganapriya3820012AU, ChennaiMaterials, Design, Manufacturingmogana98@kongu.ac.in9976855006
18Dr.N.Baaskaran3420037AU, ChennaiFinite Element Analysisbaaskararcher@kongu.ac.in9942026262
19Dr.P.C.Murugan3520010AU, ChennaiRenewable Energy, Thermal Engineering, Alternate Fuels, CFDmurugan.mech@kongu.acin9500968262
20Dr.P.Saji Raveendran3120047AU, ChennaiThermal Engineeringsaji.mech@kongu.ac.in9790432974


Research Scholars

Sl. No.Name of the ScholarReg. No.Name of the UniversityName of the SupervisorResearch AreaStatus
1Dr.R.Parameshwaran2004269113AU, Chennai Dr.PSS.SrinivasanDevelopment of an Intergrated closed loop performance management model service IndustriesCompleted on 21.10.2009
2Dr.P.Tamil Selvan2003269713AU, Chennai Dr.PSS.SrinivasanDesign and Development of condenserCompleted on 18.02.2010
3Dr.K.Visagavel2004269119AU, Chennai Dr.PSS.SrinivasanComputional Fluid DynamicsCompleted on 16.09.2010
4Dr.R.Kumaravelan2003269714AU, Chennai Dr.E.VallinayagamEnhancement of existing Design MethodologyCompleted on 18.03.2011
5Dr.V.Hariharan2004269103AU, Chennai Dr.PSS.SrinivasanStudy of vibration signature of bearings for fault deduction and condition monitoringCompleted on 29.04.2011
6Dr.K.Senthil Kumar2003269712AU, Chennai Dr.PSS.SrinivasanDesign and Development of Human Comfprt systemCompleted on 08.07.2011
7Dr.G.Arun Kumar2004269101AU, Chennai Dr.PSS.SrinivasanComplaint MechanismCompleted on 07.09.2011
8Dr.G.Nallakumarasamy 2004269108AU, Chennai Dr.PSS.SrinivasanReliability EngineeringCompleted on 03.01.2012
9Dr.K.K.Ramasamy2003269711AU, Chennai Dr.PSS.SrinivasanStudies on the performance of natural circulation, forced circulation and wind assisted domestic solar hot water systemsCompleted on 10.04.2012
10Dr.M.Ravikumar2004269109AU, Chennai Dr.PSS.SrinivasanAnalysis of natural cooling of building using phase change materialsCompleted on 31.07.2012
11Dr.P.Sathiamurthi2004269110AU, Chennai Dr.PSS.SrinivasanPerformance Study of Air Conditioner Waste Heat Recovery SystemCompleted on 13.09.2012
12Dr.T.P.Sathishkumar100930321036AUT, CBEDr.P.NavaneethakrishnanInvestigation on the performance of snake grass fiber reinforced polyester compositesCompleted on 21.01.2014
13Dr.S.Velumani7073032162AUT, CBEDr.P.NavaneethakrishnanA study on the mechanical and machinability behaviors of coir/sisal hybrid fiber reinforced vinyl ester compositesCompleted on 06.08.2014
14Dr.V.R.Muruganantham100910321023AUT, CBEDr.P.NavaneethakrishnanProcess and product innovation through lean, DFM and TRIZ conceptsCompleted on 15.10.2014
15Dr.P.Ramaswami903107AUT, CBEDr.P.Senthil VelmuruganComputational and experimental studies on effect of ovality in reformer inlet pigtail pipe bendsCompleted on 07.03.2017
16Dr.G.Rajeshkumar1314269223AU, Chennai Dr.V.HariharanInvestigations on Development and Characterization of Phoenix sp. Fiber and its Epoxy CompositesCompleted on 23.03.2017
17Dr.M.Vijayakumar71030321110AUT, CBEDr.P.NavaneethakrishnanExperimental investigations on thernmal characteristics of sintered wick heat pipe ny varying working fluidsCompleted on 14.07.2017
18Dr.V.Velmurugan10900331090AU, Chennai Dr.K.PonappaSynthesis and characterization of biodiesel from ceibapenthandra and its performance study in VCR engineCompleted on 26.02.2018
19Dr.N.Venkatachalam11230331122AUT, CBEDr.P.NavaneethakrishnanInvestigations on the suitability of passiflora foetida fiber composites with sawdust for paperboard industryCompleted on 23.03.2018
20Dr.K.Velusamy10096321053AUT, CBEDr.P.NavaneethakrishnanCertain investigations on characterization of calotropis gigantea fiber and its compositesCompleted on 30.07.2018
21Dr.M.Sambathkumar71130331056AUT, CBEDr.P.NavaneethakrishnanInvestigations on mechanical, wear and corrosion behaviour of Al7075-(SiC/TiC) hybrid metal matrix compositesCompleted on 15.02.2019
22Dr.N.Baaskaran1414269131AU, Chennai Dr.K.PonappaAssessment of crashworthiness characteristics of thin-walled cylinders subjected to axial and oblique loads Completed on 14.05.2019
23Dr.K.Karthikeyan100910321017Anna University of Technology, CoimbatoreDr.P.SomasundaramInvestigation on performance of vapour compression refrigeration system of an automobile airconditioner using ecofriendly refrigerantsCompleted on 31.05.2019
24Dr.C.Muthukumar11240331052AUT, CBEDr.P.NavaneethakrishnanInvestigations on mechanical and thermal behavior analysis of coccinia indica fiber compositesCompleted on 13.08.2019
25Dr.C.Mogana Priya1424269117AU, Chennai Dr.R.RajasekarAn experimental investigation on the influence of coating material on the machining characterstics of cutting tool insertsCompleted on 03.09.2019
26Dr.K.Ramachandran11240331078AUT, CBEDr.P.NavaneethakrishnanInvestigation of dispersion, stability and lubricating performance of nickel oxide nanolubricantsCompleted on 28.01.2020
27Dr.R.Thavamani1314269782AU, Chennai Dr.V.BalusamyA study on effect of filler metals and heat input on weldability of inconel 617 and inconel 718 alloys and improvement of weldability through ultrasonic vibrationCompleted on 12.03.2020
28Dr.T.Tamilarasi1424269813AU, Chennai Dr.R.RajasekarAn experimental investigation on analyzing the deat transfer characteristics of graphene and carbon nanotube coated microprocessorsCompleted on 08.07.2020
29Dr.K.Kathirvel1414269821AU, Chennai Dr.R.RajasekarAn experimental investigation on the influence of calcium titanium oxide and titanium dioxide coating on the voltage generation capacity of silicon solar cellCompleted on 16.07.2020
30Dr.K.A.Ibrahim Sheriff1218269757AU, Chennai Dr.V.HariharanExperimental investigations on fault diagnosis of ball bearing with solid contaminationCompleted on 03.09.2020
31Dr.V.K.Gobinath18142691149AU, Chennai Dr.P.Senthil VelmuruganSurface engineering of zinc aluminium oxide and zinc aluminium sulphide films for improving the performance of polycrystalline silicon solar cellsCompleted on 19.01.2021
32Dr.K.M.Arunraja1514269113AU, Chennai Dr.S.SelvakumarSimulation and optimization of machining fixture layout for minimum workpiece deformation using DOE and FEMCompleted on 04.08.2021
33Dr.T.Mrunalini1424369756AU, Chennai Dr.R.RajasekarCertain investigations on drug transport in-vitro model for skin cancer therapy and endosment of graphene in biosensing platform for cancer therapeuticsCompleted on 31.05.2022
34Dr.S.Arun Kumar1414269832AU, Chennai Dr.R.RajasekarExperimental investigation on analyzing the performance of spinel nanoparticle anti-reflection coating on the power conversion efficiency of polycrystalline solar cells Completed on 21.07.2022
35Dr.S.Santhosh19142697256AU, Chennai Dr.R.RajasekarExperimental investigation on the power conversion efficiency performance of molybdenum diselenide and zinc oxide-tantalum pentoxide deposited multicrystalline silicon solar cellsCompleted on 02.09.2022
36Dr.S.Prashanth1514269193AU, Chennai Dr.R.RajasekarPerformance evaluation of power conservation efficiency attainment in polycrystalline silicon solar cells through sputter and spin coated molybdenum disulphide antireflecting layersCompleted on 16.09.2022
37Dr.N.Bagath Singh17132691238AU, Chennai Dr.A.SivakumarInvestigation and optimization of production parameters for the bus body building industry using metaheuristic searchCompleted on 30.09.2022
38Dr.S.Satheeshkumar16142697168AU, Chennai Dr.T.P.SathishkumarInvestigation on the long term mechanical performance and quasi static compressive properties of jute fiber reinforced epoxy compositesCompleted on 23.11.2022
39Dr.B.S.Hari1414269122AU, Chennai Dr.R.RajasekarSpecific investigations on analyzing the reinforcement effect of several particulates in characteristics of nylonCompleted on 06.03.2023
40Mr.C.Sathish Ranganathan1414269112AU, Chennai Dr.R.RajasekarStudies on the physico-mechanical behavior of carbon based nano filler reinforced rubber nano compositePursuing
41Mr.N.Saravanan1414269118AU, Chennai Dr.R.RajasekarInvestigation on the effect of functionalised graphene on the properties of polymer nanocompositesPursuing
42Mr.M.Gopi23142691121AU, Chennai Dr.R.RajasekarDevelopment of speedy roof and side wall crack arrester in underground mines using appropriate polymeric nanocompositesPursuing
43Mr.N.Vadivel11160331074AU, ChennaiDr.P.SomasundaramExperimentation investigations on dual fulled HCCI enginePursuing
44Mr.N.Prasanna17152691344AU, ChennaiDr.P.SomasundaramPerformance enhancement of solar still using air refrigeration systemPursuing
45Mr.T.Rajagopal17142691343AU, ChennaiDr.P.SomasundaramInvestigation of rankine cycle using internal combustion engine waste heat recoveryPursuing
46Mr.R.Chandramohan17142691342AU, ChennaiDr.P.SomasundaramOptimum new refrigerant solution for GWP and ODP issuesPursuing
47Mr.S.Ajay17152697196AU, ChennaiDr.P.SomasundaramPerformance enhancement and emission reduction in IC enginesPursuing
48Mr.S.Sathishkumar19142697113AU, ChennaiDr.P.SomasundaramInfluence of injection timing and split injection strategies on combustion performance and emission characteristics of a diesel engine fueled with bidiesel blended fuelsPursuing
49Mr.N.Boopalan21142691150AU, ChennaiDr.P.SomasundaramExperimental study on performance of common rail direct injection engine with multiple injection strategiesPursuing
50Mr.P.Gnaneswaran1314269110AU, Chennai Dr.V.HariharanCharacterization and analysis of particle reinforced aluminium metal matrix composites using squeeze casting methodPursuing
51Mr.M.Dharmaraj1314269160AU, Chennai Dr.V.HariharanFailure analysis of contact separation in hot-fit rotating componentsPursuing
52Mr.K.Vigneshwaran18142691168AU, Chennai Dr.V.HariharanInvestigations on dynamic characteristics of polymer matrix compositesPursuing
53Mr.R.Kamalakannan18142697157AU, Chennai Dr.K.DineshkumarCorrosion behaviour of a light materialsPursuing
54Mr.S.Jeeva20142691196AU, Chennai Dr.K.DineshkumarSynthesis of tire materials with nano-polymers and evaluation of mechanical and tribological characteristics Pursuing
55Mr.P.Praveen1614269264AU, Chennai Dr.S.SelvakumarFixture design optimization using non traditional algorithmsPursuing
56Mr.G.Chandramohan18142691155AU, Chennai Dr.S.SelvakumarStudy on property enhancement of metal matrix compositesPursuing
57Mr.S.Ranjithkumar1614269258AU, Chennai Dr.S.SelvakumarCondition monitoring techniques to predict failure of automotive componentsPursuing
58Mr.T.Ravisankar21122691268AU, Chennai Dr.S.SelvakumarDesign and parametric analysis of solar thermal cookersPursuing
59Mr.Ra.Aravind21142691210AU, Chennai Dr.S.SelvakumarErgonomic investigations on work-related hand arm vibration disorders among power tool workersPursuing
60Mr.A.Abubakkar21182697144AU, Chennai Dr.S.SelvakumarInvestigation of CO2 capture and storage techniques with prototype developmentPursuing
61Ms.T.Jeevetha17241691116AU, Chennai Dr.A.SivakumarInvestigate, Design and Optimize the Reinforced Concrete and Frame Characteristics using Artificial Intelligent TechniquesPursuing
62Mr.K.S.Karthi Vinith17142691121AU, Chennai Dr.A.SivakumarInvestigation on auto components quality and defects using sensor based model with artificial intelligencePursuing
63Mr.S.Saravanakumar17122697155AU, Chennai Dr.A.SivakumarOptimization of process variables by the applications of agile manufacturing for manufacturing industryPursuing
64Mr.H.Vinoth Kumar17142697306AU, Chennai Dr.A.SivakumarDesign investigate and analysis of drilling work table through ergonomics techniquesPursuing
65Mr.D.Suresh20142691105AU, Chennai Dr.A.SivakumarAn empirical study, analysis and investigation about impact of schedule management plan in project management effectiveness using structural equation modellingPursuing
66Mr.M.Mahesh18152697161AU, Chennai Dr.P.ThangavelInvestigation on performance analysis of the solar operated cascade refrigeration system using eco-friendly refrigerantsPursuing
67Mr.R.Karthikeyan20132691156AU, Chennai Dr.P.ThangavelInvestigation of heat and mass transfer study on drying of agricultural food products using sustainable solar energyPursuing
68Mr.M.Makeshkumar20142691157AU, Chennai Dr.P.ThangavelInvestigations on thermal management system for batteries employed in electric vehiclesPursuing
69Mr.K.V.Satheesh Kumar21122691108AU, Chennai Dr.P.ThangavelOptimization on thermal behaviour of powered food products under different climatic conditionsPursuing
70Mr.N.S.Nandakumar18142697121AU, Chennai Dr.K.S.K.Sasikumarmacro and micro machining of hybrid aluminum metal matrix compositesPursuing
71Ms.K.Megala18222691293AU, Chennai Dr.K.S.K.SasikumarAnalysis of magnesium metal matrix comopsitesPursuing
72Mr.M.Arul18142691222AU, Chennai Dr.K.S.K.SasikumarAnalysis of fracture toughness in natural fiber reinforced polymer composites system for automotive applicationsPursuing
73Mr.S.Karthi21142691173AU, Chennai Dr.K.S.K.SasikumarCharacterization of defects in aluminium composites by state of the art non destructive testing methodsPursuing
74Mr.K.Ramachandran20132691226AU, Chennai Dr.P.SelvakumarVibration analysis on polymer nano compositesPursuing
75Mr.K.S.Manoj21142691264AU, Chennai Dr.P.SelvakumarDesign of heat sink for thermal management of batteries in electric vehiclesPursuing
76Mr.A.Ganesh22142691266AU, Chennai Dr.P.SelvakumarPerformance studies on hybrid pyramid solar stillPursuing
77Mr.M.M.Jegan16142697181AU, Chennai Dr.T.P.SathishkumarInvestigation on the fracture and creep behavior of the synthetic and natural fiber laminate polymer compositePursuing
78Mr.Pon.Maheskumar16142697135AU, Chennai Dr.T.P.SathishkumarMechanical and tribological behaviours of natural fibre and natural filler reinforced biodegradable polymer compositesPursuing
79Mr.M.Muralidharan16132697244AU, Chennai Dr.T.P.SathishkumarInvestigation on the mechanical and tribological behaviour of coconut sheel and graphite fillers in kevlar fiber laminate polymer compositePursuing
80Mr.G.Manikandan21142691230AU, ChennaiDr.T.P.SathishkumarExperimenmtal analysis of composite materials for automobilePursuing
81Mr.P.Senthil Kumar19142691105AU, ChennaiDr.T.P.SathishkumarDevelopment, testing and analysis of mechanical properties of natural fiber semi metallic rubber composite friction material for dry clutch Pursuing
82Mr.C.M.Dinesh23122691123AU, Chennai Dr.M.BhuvaneshkumarParameter optimization and microstructural investigatyions on the addtively manufactured inconel alloy thin-walled structuresPursuing
83Mr.A.Saravanan21142691169AU, Chennai Dr.R.NaveenkumarErgonomic evaluation of work related musculoskeletal disorder among agricultural workersPursuing
84Mr.S.Mohankumar21142691211AU, Chennai Dr.R.NaveenkumarEvaluation of work related musculoskeletal disorder among unorganised small scale industry workersPursuing
85Mr.S.Venkatachalam21131691135AU, Chennai Dr.R.NaveenkumarPerformance evaluation of low cost building panelPursuing
86Mr.G.Arun Prasad1512289217AU, Chennai Dr.P.C.Murugan
(Joint Supervisor)
Investigation on the performance of IC engines operated with PG from the blends of locally available biomassesPursuing


Journals

Sl. No.Title of the paperName of the journalInternational / NationalVol. No. / Issue No./ Page No. / YearAuthors
1An experimental investigation on a locally fabricated dryer integrated with a novel solar air heater for the drying of potato slicesEnergy Sources, Part A: Recovery, Utilization, and Environmental EffectsInternationalVol.44, No.4
pp.9811-9826
November 2022
S.Pandiaraj
T.Ayyasamy
M.Hasanuzzaman
G.Angappan
S.Muthusamy
H.Panchal
S.C.M.Sundararajan
2Multi criteria decision making through TOPSIS and COPRAS on drilling parameters of magnesium AZ91Journal of magnesium and alloysInternationalVol.10, No.10
pp.2857-2874
November 2022
M.Varatharajulu
M.Duraiselvam
M.B.Kumar
G.Jayaprakash
N.Baskar
3Feasibility study on raw Simarouba glauca oil as an alternate fuel in a diesel engine and comparative assessment with its esterified oilFuelInternationalVol.327, p.125168
November 2022
A.Tamilvanan
P.Jeyalakshmi
M.Mohanraj
B.Deepanraj
4Physicochemical and thermal properties of cellulosic fiber extracted from the bark of albizia samanJournal of Natural FibersInternationalVol.19, No.13
pp.6659-6675
November 2022
R.Gopinath
P.Billigraham
T.P.Sathishkumar
5Physico-mechanical, chemical composition and thermal properties of cellulose fiber from Hibiscus vitifolius plant stalk for polymer compositesJournal of Natural FibersInternationalVol.19, No.13
pp.6961-6976
November 2022
S.Manivel
N.Pannirselvam
R.Gopinath
T.P.Sathishkumar
6Characterization Studies on New Natural Cellulosic Fiber Extracted from the Bark of Erythrina variegateJournal of Natural FibersInternationalVol.19, No.14
pp.8246-8265
November 2022
R.Gopinath
P.Billigraham
T.P.Sathishkumar
7Physicochemical and thermal properties of new cellulosic fiber obtained from the stem of Markhamia luteaJournal of Natural FibersInternationalVol.19, No.14
November 2022
R.Gopinath
P.Billigraham
T.P.Sathishkumar
8Characterization of Sida acuta fiber and its polymer composites with effect of fly ashJournal of Natural FibersInternationalVol.19, No.14
pp.8811-8829
November 2022
R.Gopinath
P.Billigraham
T.P.Sathishkumar
M.R.Sanjay
S.Siengchin
9Investigation of Physico-chemical, Mechanical, and Thermal Properties of New Cellulosic Bast Fiber Extracted from the Bark of Bauhinia purpureaJournal of Natural FibersInternationalVol.19, No.14
pp.9624-9641
November 2022
R.Gopinath
P.Billigraham
T.P.Sathishkumar
10Influence of Alkali Treatment on Physicochemical, Thermal and Mechanical Properties of Hibiscus Vitifolius FibersJournal of Natural FibersInternationalVol.19, No.15
pp.11708-11721
November 2022
S.Manivel
N.Pannirselvam
R.Gopinath
T.P.Sathishkumar
11Physicochemical, Thermal And Mechanical Properties of Novel Cellulosic Fiber Extracted from Ficus RetusaJournal of Natural FibersInternationalVol.19, No.16
pp.14706-14724
November 2022
R.Gopinath
P.Billigraham
T.P.Sathishkumar
R.Rajasekar
12Characterization Studies on Novel Cellulosic Fiber Obtained from the Bark of Madhuca Longifolia TreeJournal of Natural FibersInternationalVol.19, No.16
pp.14880-14897
November 2022
R.Gopinath
P.Billigraham
T.P.Sathishkumar
13Investigation on Physicochemical, Thermal and Mechanical Properties of New Cellulosic Fiber Obtained from the Stem of Tecoma StansJournal of Natural FibersInternationalVol.19, No.16
pp.14975-14993
November 2022
R.Gopinath
P.Billigraham
T.P.Sathishkumar
14Fabrication of LLDPE based biodegradable composite incorporated with leather shavings and buffing dust: An approach for waste managementJournal of Applied Polymer ScienceInternationalVol.139, No.47
p.e53184, November 2022
M.A.R.Noyon
T.K.Dey
M.Jamal
R.Rajasekar
M.Chinnasamy
M.E.Uddin
15Investigation of TiAlN, AlTiN, and TiAlSiN Coated Inserts on the Machining Performance of AISI 420 Steel and Multi-Objective Optimization of Process ParametersJournal of The Institution of Engineers (India): Series DInternationalVol.103, No.2
pp.563-573
November 2022
M.Chinnasamy
R.Rajasekar
S.K.Palaniappan
S.K.Pal
16Energy management system for charging stations for electric and hydrogen vehicles using solar, hydrogen and fuel cell technologyIn AIP Conference ProceedingsInternationalVol.2519, p.050059
October 2022
E.F.I.Raj
A.Saravanan
U.Durairaj
S.Selvakumar
B.S.Sagar
M.Ganavi
G.Pavithra
17Interpretation of the performance and emission characteristics of a CI engine running on ethanol-butanol diesel blends using an optimisation modelInternational Journal of Heavy Vehicle SystemsInternationalVol.29, No.2
pp.180-196
October 2022
S.Ajay
P.Somasundaram
N.Prasanna
T.Rajagopal
18Optimization of geometric parameters for mode-I fracture analyse on glass fiber woven mat thermoplastic laminated compositesMaterials Today: ProceedingsInternationalVol.52, pp.2474-2478
October 2022
T.P.Sathishkumar
P.Navaneethakrishnan
M.R.Sanjay
S.Siengchin
S.Karthi
19Sustainable Hard Machining of AISI 304 Stainless Steel Through TiAlN, AlTiN, and TiAlSiN Coating and Multi-Criteria Decision Making Using Grey Fuzzy Coupled Taguchi MethodJournal of Materials Engineering and PerformanceInternationalVol.31, pp.7302-7314
October 2022
C.Moganapriya
R.Rajasekar
R.Santhosh
S.Saran
S.Santhosh
V.K.Gobinath
P.S.Kumar
20Effect of Silicon Carbide and Alumina Reinforcement of Different Volume Fraction on Wear Characteristics of AL 7075 Hybrid Composites Using Response Surface MethodologyMaterials ResearchInternationalVol.25, September 2022R.Gukendran
M.Sambathkumar
K.S.K.Sasikumar
D.K.Karupannasamy
21Performance analysis of greenhouse solar dryer using evacuated tubesMaterials Today: ProceedingsInternationalVol.66, pp.1509-1513
September 2022
R.Karthikeyan
P.Thangavel
R.T.Raghunath
K.M.Priyan
M.P.Balaji
22Experimental analysis of semi-automatic drainage cleanerMaterials Today: ProceedingsInternationalVol.66, pp.1492-1496
September 2022
P.S.Raveendran
S.P.Malai
R.N.Raj
V.Naveen
J.S.Binoj
23Effect of Titanium Based Alloys on Thermo-Mechanical Behavior in 3D Forging SimulationMetalsInternationalVol.12, No.10 p.1611
September 2022
Mohan Kumar Anand Raj
Balaji Madheswaran
Ali Jawad Alrubaie
Hitesh Panchal
Suresh Muthusamy
Mustafa Musa Jaber
Chander Prakash
Joao Paulo Davim
Kuldeep Kumar Saxena
Dharam Buddh
24Forecasting the Equipment Effectiveness in Total Productive Maintenance Using an Intelligent Hybrid Conceptual ModelTransactions of FAMENAInternationalVol.46, No.3 pp.29-40
September 2022
A.Sivakumar
S.Saravanakumar
P.Sathiamurthi
K.S.KarthiVinith
25Evaluation of the Efficacy in Ergonomically Designed Handsaw to Minimize the Muscular Load on Arm and Shoulder Muscles among CarpentersJournal of The Institution of Engineers (India): Series CInternationalVol.103, No.5
pp.1125-1132
September 2022
R.Naveenkumar
S.Shankar
R.Nithyaprakash
D.Hariprasath
G.Moulidaman
C.Prakash
26Influence of Electrosprayed MoSe2 Antireflective Surface Coatings on Performance of Multicrystalline Silicon Solar CellSiliconInternationalVol.14, pp.6039-6051
August 2022
S.Santhosh
R.Rajasekar
V.K.Gobinath
C.Moganapriya
S.Arun Kumar
A.Manju Sri
27Evaluation of oxidation stability and engine behaviors operated by Prosopis juliflora biodiesel/diesel fuel blends with presence of synthetic antioxidantSustainable Energy Technologies and AssessmentsInternationalVol.52, Article ID: 102086
August 2022
S.Rajamohan
A.H.Gopal
K.R.Muralidharan
Z.Huang
B.Paramasivam
T.Ayyasamy
A.T.Hoang
28Biofuel powered engine characteristics improvement through split injection parameter multivariate optimization with titanium based nano-particle additivesFuelInternationalVol.322, Article ID: 124178
August 2022
T.S.Kumar
B.Ashok
M.S.Kumar
R.Vignesh
P.Saiteja
K.R.B.Hire
T.Ayyasamy
29Effect of Aluminium Oxide Nano Additive on Diesel along with Gasoline Fumigation in Single Cylinder Diesel EngineJournal of Engineering ResearchInternationalVol.10, pp.145-155
August 2022
M.Bharathiraja
A.Tamilvanan
K.Balamurugan
C.Sasikumar
30Biodegradable Magnesium Metal Matrix Composites for Biomedical Implants: Synthesis, Mechanical Performance, and Corrosion Behavior-A ReviewJournal of Materials Research and TechnologyInternationalVol.20, pp.650-670
August 2022
R.Krishnan
S.Pandiaraj
S.Muthusamy
H.Panchal
M.S.Alsoufi
A.M.M.Ibrahim
A.Elsheikh
31Cladding phase change materials in freezing and chilling zones of household refrigerator to improve thermal performance and environmental benefitsJournal of Energy StorageInternationalVol.55, Article ID: 105476
August 2022
S.J.Sekhar
M.A.F.Raj
P.S.Raveendran
P.C.Murugan
322D FEM simulation and experimental verification of Al 7075-T6 during turning processMaterialwissenschaft und WerkstofftechnikInternationalVol.53, No.7
pp.781-789
July 2022
A.Mohan Kumar
R.Rajasekar
R.Parameshwaran
33A study of solar heat gain variation in building applied photovoltaic buildings and its impact on environment and indoor air qualityEnergy Sources, Part A: Recovery, Utilization, and Environmental EffectsInternationalVol.44, No.3
pp.6192-6212
July 2022
S.Pandiaraj
A.Abdul Jaffar
S.Muthusamy
H.Panchal
S.Pandiyan
34A case study on development of thermodynamic entropy measuring device and its implication on the human bodyCase Studies in Thermal EngineeringInternationalVol.37, Article ID: 102229
July 2022
S.Pandiaraj
K.Govindasamy
A.Pandey
C.Sonawane
A.J.Alrubaie
A.Majdi
H.Panchal
35Experimental and empirical analysis of a diesel engine fuelled with ternary blends of diesel, waste cooking sunflower oil biodiesel and diethyl etherFuelInternationalVol.320, Article ID: 12396
July 2022
B.D.Naik
U.Meivelu
V.Thangarasu
S.Annamalai
V.Sivasankaralingam
36Impact of exhaust gas recirculation and split injection strategy combustion behavior on premixed charge compression ignition engine fuelled with moringa oleifera methyl esterFuelInternationalVol.319, Article ID: 123702
July 2022
S.Ramalingam
D.Babu
A.Santhoshkumar
R.Deepakkumar
D.Ravikanth
37Micro-structure and self-lubricant properties of powder mixed electrical discharge metal matrix composite coating Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical EngineeringInternationalVol.236, No.4
pp.1369-1376
July 2022
I.Arun
C.Yuvaraj
A.Sivakumar
S.Thamizhmanii
38Effectiveness of cryogenic treatment on cutting tool inserts: A reviewInternational Journal of Refractory Metals and Hard MaterialsInternationalVol.108, Article ID: 105946
July 2022
M.Chinnasamy
R.Rathanasamy
S.K.Pal
S.K.Palaniappan
39Engineered polymer matrix novel biocompatible materials decorated with eucalyptus oil and zinc nitrate with superior mechanical and bone forming abilitiesArabian Journal of ChemistryInternationalVol.15, No.9
Article ID: 104079
July 2022
M.P.Mani
A.A.M.Faudzi
S.Mohamaddan
A.F.Ismail
R.Rathanasamy
M.Ayyar
S.K.Jaganathan
40Analysis of SiC grinding wheel wear and surface roughness in machining of Al2O3 advanced ceramic using regression modelSurface Review and LettersInternational Vol.29, No.6
Article ID: 2250080
June 2022
P.Kanakarajan
C.Moganapriya
R.Rajasekar
S.Sundaram
M.Syed Thasthagir
S.Soundararajan
K.M.Barath
41Effect of interfacial thickness on microstructure, mechanical properties, and modelling of diffusion fused dissimilar Al alloys for process optimization using ANN-GA methodMultiscale and Multidisciplinary Modeling, Experiments and DesignInternationalVol.5, No.2
pp.105-117
June 2022
A.Britto
J.S.Binoj
N.Manikandan
G.M.Surendranatha
B.Naidu
P.S.Raveendran
42Investigation on the microstructure and microhardness of Inconel 825 thick wall fabricated by wire arc additive manufacturingMaterials LettersInternationalVol.317
p.132115, 2022
M.Bhuvanesh Kumar
P.Sathiya
G.Rajesh Kannan
M.Karthikeyan
43A Review on Drilling of Fiber-Reinforced Polymer CompositesMechanics of Composite MaterialsInternationalVol.58, No.1
pp.1-16, 2022
A.M.Kumar
R.Parameshwaran
R.Rajasekar
C.Moganapriya
R.Manivannan
44Investigation on Mechanical and Wear Behaviors of LM6 Aluminium Alloy-Based Hybrid Metal Matrix Composites using Stir Casting ProcessAdvances in Materials Science and EngineeringInternationalVol.2022
Article ID:4116843, 2022
P.Gnaneswaran
V.Hariharan
S.J.S.Chelladurai
G.Rajeshkumar
S.Gnanasekaran
S.Sivananthan
B.Debtera
45Performance studies on vapour compression refrigeration system using PCM placed between wall and coil of the evaporatorProceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical EngineeringInternationalVol.236,No.2
pp.582-588, 2022
P.S.Raveendran
R.Karthikeyan
P.C.Murugan
S.Sanjay
S.Vivek Raj
N.K.Selva Kannan
D.K.John
46A waste to energy technology for Enrichment of biomethane generation: A review on operating parameters, types of biodigesters, solar assisted heating systems, socio economic benefits and challengesChemosphereInternationalVol.293
p.133486, 2022
N.Kalaiselvan
G.Glivin
A.K.Bakthavatsalam
V.Mariappan
M.Premalatha
P.S.Raveendran
S.J.Sekhar
47Grapefruit Oil and Cobalt Nitrate-Loaded Polyurethane Hybrid Nanofibrous Scaffold for Biomedical ApplicationsFrontiers in MaterialsInternationalVol.9
p.827009, 2022
M.P.Mani
A.A.M.Faudzi
S.Mohamaddan
A.F.Ismail
R.Rathanasamy
M.Ayyar
S.K.Jaganathan
48Behavior of epoxy reinforced banana glass fiber hybrid composite with nanoclay interferenceProceedings of The Institution of Mechanical Engineers Part C-Journal of Mechanical Engineering ScienceInternationalVol.236, No.6
pp.2995-3003, 2022
M.Sudhagar
T.K.Kannan
S.B.Lazarus
R.Rajasekar
S.S.Raj
49Investigation of mechanical properties of dual-fiber reinforcement in polymer compositeJournal of Materials Research and TechnologyInternationalVol.18, pp.3908-3915
2022
M.K.A.Raj
S.Muthusamy
H.Panchal
A.M.M.Ibrahim
M.S.Alsoufi
A.H.Elsheikh
50An extensive review of performance enhancement techniques for pyramid solar still for solar thermal applicationsDesalinationInternationalVol.532, p.115692
2022
G.Angappan
S.Pandiaraj
H.Panchal
T.Kathiresan
D.Ather
C.Dutta
K.K.Sadasivuni
51Long?term environmental bending behaviors and service LIFE prediction of KEVLAR fiber mat epoxy compositePolymer CompositesInternationalVol.43, No.4
pp.2396-2407, 2022
M.Muralidharan
T.P.Sathishkumar
J.de?Prado?Gil
R.Martínez?García
52Multi-response Optimization for Evaluating Output Responses in Rock Cutting Through Grey-Fuzzy-Coupled Taguchi TechniqueMining, Metallurgy & ExplorationInternationalVol.39, No.3
pp.1133-1148, 2022
S.K.Palaniappan
S.K.Pal
M.Chinnasamy
R.Rathanasamy
G.V.Kaliyannan
53Influence of ZnSe Surface Coatings for Enhancing the Performance of Multicrystalline Silicon Solar CellsJournal of Electronic MaterialsInternationalVol.51, No.6
pp.2833-2842, 2022
M.Chinnasamy
R.Rathanasamy
S.Sivaraj
G.VeluKaliyannan
M.S.Anbupalani
S.K.Jaganathan
54Mechanical, Thermal and Ablative Properties of Silica, Zirconia and Titania Modified Carbon-Phenol Ablative CompositesAdvances in Materials Science and EngineeringInternationalVol.2022
Article ID: 7808587, 2022
R.R.P.Kuppusamy
S.Neogi
S.Mohanta
M.Chinnasamy
R.Rathanasamy
M.Uddin
55Optimization of stir casting process parameter using response surface methodologyJournal of Ceramic Processing ResearchInternationalVol.23, No.2
pp.233-236, 2022
K.M.Senthilkumar
A.Sivakumar
RohokaleMilindShivaji
S.K.Tamang
M.Giriraj
56Mathematical modelling and analysis of domestic refrigerator with alternative Eco-friendly refrigerants for R134aJournal of environmental protection and ecologyInternationalVol.23, No.2
pp.474-486, 2022
M.Mahesh
P.Thangavel
57Effect of Cloisite 15A on the mechanical properties of an abaca-based compositeMaterials TestingInternationalVol.64, No.1
pp.125-131
February 2022
M.K.Anandraj
P.Rathinasamy
S.K.Palaniappan
58Crashworthiness unit cell design investigation for energy absorption analysisMaterials Today: ProceedingsInternationalVol.50, pp.1282-1290
February 2022
M.Dharmaraj
C.Sridhar
59Flexural and crashworthiness studies of friction stir welded aluminum alloy pipesMaterials Today: ProceedingsInternationalVol.50, pp.977-980
February 2022
S.M.Senthil
M.Sradeep
K.Sharan
P.A.Selvapravin
60Machining parameters in WEDM of EN31 steel using Taguchi technique optimizationMaterials Today: ProceedingsInternationalVol.50, pp.1781-1785
February 2022
R.Kamalakannan
G.M.Pradeep
T.NaveenKumar
M.Elango
61The sliding wear behavior of CrCuFeNi alloyed with various combinations of cobaltMaterials Today: ProceedingsInternationalVol.50, pp.1814-1817
February 2022
R.Kamalakannan
K.DineshKumar
K.NarenRaj
62Effect of Tool Rotational Speed and Traverse Speed on Friction Stir Welding of 3D-Printed Polylactic Acid MaterialApplied Science and Engineering ProgressInternationalVol.15, No.1
January 2022
S.M.Senthil
M.B.Kumar
63Energy Analysis of R1234yf/R134a as Replacement of R134a in a Domestic RefrigeratorAdvancement in Materials, Manufacturing and Energy EngineeringInternationalVol.2, pp.495-502
January 2022
P.Saji Raveendran
P.C.Murugan
T.Darwin
G.Glivin
G.Dwivedi
64A Predictive Model for Galling Phenomenon and Its Applicability for Deep Drawing ProcessesJournal of TribologyInternationalVol.144, No.1
p.011705, January 2022
D.K.Karupannasamy
S.V.Kailas
S.Shankar
K.S.K.Sasikumar
65Improvement of the mechanical and damping behavior of nylon by integration of nano clay plateletsMaterials TestingInternationalVol.63, No.12
pp.1124-1129
December 2021
H.B.Subburamamurthy
R.Rathanasamy
H.K.M.Kumar
M.Chinnasamy
G.V.Kaliyannan
S.Natarajan
66Characterization of chemically treated new natural cellulosic fibers from peduncle of Cocos nucifera L. VartypicaPolymer CompositesInternationalVol.42, No.12
pp.6403-6416
December 2021
B.M.Bright
B.Joseph Selvi
S.Abu Hassan
M.Mustapha Jaafar
S.Siengchin
S.MavinkereRangappa
S.R.Padmavathy
67An extensive analysis of mechanical, thermal and physical properties of jute fiber composites with different fiber orientationsCase Studies in Thermal EngineeringInternationalVol.28, p.101612
December 2021
G.Rangasamy
S.Mani
S.K.S.Kolandavelu
M.S.Alsoufi
A.M.M. Ibrahim
S.Muthusamy
A.H.Elsheikh
68Extremal-Micro Genetic Algorithm Model for time-cost optimization with optimal labour productivityJournal of Mechanical EngineeringInternationalVol.67, No.12
pp.682-691
December 2021
A.Sivakumar
N.Bagath Singh
P.Sathiamurthi
K.S.KarthiVinith
693-3-1 machining fixture scheme optimization using genetic algorithm and FEMIn AIP Conference Proceedings, AIP Publishing LLCInternationalVol.2387, No.1
p.110003, December 2021
K.M.Arunraja
S.Selvakumar
70Adaptive threshold and modified adaptive gain function based speech enhancement algorithm for digital hearing aidSmart technologies, communication & robotics, Smart Technologies, Communication and Robotics Internationalpp.1-5, December 2021Deepa Dhanaskodi
Poongodi Chenniappan
K.Shoukath Ali
T.Perarasi
P.Thangavel
71Super capacitor based solar and wind grid connected storage systemIEEE Xplore -Third International Conference on Inventive Research in Computing ApplicationsInternationalpp. 218-225
November 2021
M.SivaRamkumar
G.Swapna
A.Saravanan
N.Hemalatha
GaneshaperumalDharmaraj
S.Purushotham
M.Sivaramkrishnan
72Corrosion of brass subjected to cast-off cooking oil blended with dieselMaterials TestingInternationalVol.63, No.11
pp.1032-1040
November 2021
SangeethaGovindharajan
Saratha Raman
ViswapriyaShanmugam
RajasekarRathanasamy
Sathish Kumar Palaniappan
73Assessing The Tribological Properties of Vegetable Oil Emulsions and Machining Parameter Optimization using Response Surface MethodologySurface Review and LettersInternationalVol.28, No.12
p.2150119, November 2021
K.Dinesh Kumar
M.Sambathkumar
R.Gukendran
KSK.Sasikumar
N.Baaskaran
S.Shankar
74Evaluation of tensile strength retention and service life prediction of hydrothermal aged balanced orthotropic carbon/glass and Kevlar/glass fabric reinforced polymer hybrid compositesJournal of Applied Polymer ScienceInternationalVol.139, No.6
p.51602, November 2021
M.Muralidharan
T.P.Sathishkumar
N.Rajini
P.Navaneethakrishnan
S.Arun Kumar
SikiruOluwarotimi Ismail
K.Senthilkumar
SuchartSiengchin
75The computational fluid dynamics (CFD) investigation of steam flow and temperature distribution in a small scale idly-baking ovenAIP Conference ProceedingsInternationalVol.2387, No.1
p.020001, November 2021
M.Dharmaraj
K.S.Kumar
S.Vikram
K.A.Srikishore
76Investigating the Impact of the Hoe handle Length and Angle on the Shoulder and Arm Muscle Activity during Manual Farming ActivitiesJournal of The Institution of Engineers (India): Series AInternationalVol.102, No.4
pp.1053-1060
October 2021
R.Naveen Kumar
A.Saravanan
S.Shankar
R.Nithyaprakash
B.Jaikumar
A.Mohanraj
K.Mohanprasath
77Effect of abaca reinforced polymer composite on dynamic mechanical analysisColloid and Polymer Science InternationalVol.299, No.11
pp.1657-1667
October 2021
A.Mohan Kumar
R.Parameshwaran
R.Rajasekar
78Investigation of emission and performance analysis of honne oil in VCR diesel engineJournal of Physics: Conference SeriesInternationalVol.2054, No.1
p.012065
October 2021
B. V.Subhanandh
N.Abilash
P.Saji Raveendran
79Impact of lean Implementation from the ergonomics view: A research articleMaterials Today : Proceedings InternationalVol.46, No.19
pp.9610-9612
October 2021
H.Vinoth Kumar
A.Sivakumar
BagathsinghNhsing
80A multivariate analysis and investigation on break even and productivity measures using artificial intelligence: A post research work in textile process industriesMaterials Today : ProceedingsInternationalVol.46, No.19
p.9613
October 2021
A.Sivakumar
81Investigation of Optimum Process Parameter of Lost Foam Casting of A356/SiC Metal Matrix CompositesMaterial Today Proceedings - Elsevier Publications InternationalVol.47, No.14
pp.4801-4806
October 2021
M.Vijay Anand
K.Paramasivam
M.Sambathkumar
82Vibration analysis of nylon gear box utilizing statistical methodMaterials Today proceedingsInternationalVol.33, No.7
pp.3525-3531, 2021
C.Poongodi
B.S.Hari
S.Arunkumar
83Deep Learning-Based X-Ray Baggage Hazardous Object Detection - An FPGA ImplementationInternational Information and Engineering Technology AssociationInternationalVol.35, No.5
pp.431-435
October 2021
VijayakumarPonnusamy
Diwakar R. Marur
DeepaDhanaskodi
ThangavelPalaniappan
84Pseudocapacitive characteristics of Mg Doped ZnOnanospheres prepared by coprecipitationArchives of metallurgy and materialsInternationalVol.102, No.5
pp.1261-1265
September 2021
S.Arul
T.Senthilnathan
V.Jeevanantham
K.V.Satheesh Kumar
85Performance Studies on Solar Air Heater with Staggered Open Channel Aluminium TurbulatorsJournal of The Institution of Engineers (India): Series CInternationalVol.66, No.4
pp.1141-1148
September 2021
P.Selvakumar
J.Jose Anson
V.Harish
TK.Gulshan
86Cellulose fiber from date palm petioles as potential reinforcement for polymer composites: Physicochemical and structural propertiesPolymer CompositesInternationalVol.42, No.8
pp.3943-3953
August 2021
G.Rajeshkumar
V.Hariharan
G.L.Devnani
J.Prakash Maran
M.R.Sanjay SuchartSiengchin
Naif Abdullah Al-Dhabi
K.Ponmurugan
87Analyze the Design of Leaf spring by Solid works and Ansys to Improve the Vehicle PerformanceAnnals of R.S.C.BInternationalVol.25, No.5
p.44531
August 2021
H.Vinoth Kumar
A.Sivakumar
G.Gowshik
S.Deepanraj
R.Prabakaran
88Investigation of Mechanical and Corrosion Properties of Al 7075/Garnet Metal Matrix Composites by Two-stage Stir Casting ProcessArch. Metall. MaterInternationalVol.66, No.4
pp.1123-1129
August 2021
M.Sambathkumar
P.Navaneethakrishnan
K.S.K.Sasikumar
R.Gukendran
K.Ponappa
89Improve the efficiency of battery cooling system in E Vehicle bu Nano -Fluids with CFD AnalysisIOP Conf. Series : Material Science and EngineeringInternationalVol.1126, No.1
p.44531
August 2021
H.Vinothkumar
S.Saravanakumar
A.Sivakumar
M.Gokul
S.Jagadheeswaran
M.Manikandan
90Latex reinforced waste buffing dust-jeans cotton composites and its characterizationJournal of Polymer ResearchInternationalVol.28, No.8
p.44409
August 2021
Ariful Islam
YasinMolla
Thuhin Kumar Dey
Mamun Jamal
RajasekarRathanasamy
Md. Elias Uddin
91Investigation of Dry Sliding Wear Behavior of Al 7075–(SiC/TiC) Hybrid Metal Matrix CompositesSurface Review and LettersInternationalVol.28, No.7
p.2150065
July 2021
R.Gukendran
M.Sambathkumar
K.S.K.Sasikumar
K.Ponappa
S.Gopal
92Effect of diethyl ether and ethanol as an oxygenated additive on Calophylluminophyllum biodiesel in CI engineEnvironmental Science and Pollution ResearchInternationalVol.28, No.26
pp.33880-33898
July 2021
AyyasamyTamilvanan
KulendranBalamurugan
Bragadeshwaran Ashok
PandiarajSelvakumar
SubbaiyanDhamotharan
MoorthyBharathiraja
ViswanathanKarthickeyan
93Energy and exergy analysis on hydrofluoroolefin / hydrofluorocarbon (HFO/HFC) refrigerant mixtures in low and medium temperature small-scale refrigeration systemsProceedings of the Institution of Mechanical Engineers Part E-Journal of Process Mechanical EngineeringInternationalVol.235, No.3
pp.718-730
June 2021
P.SajiRaveendran
S.Joseph Sekhar
94Utilisation of transition metal chalcogenide MoSe2 as promising antireflective coating for achieving intensified light traptionChalcogenide LettersInternationalVol.18, No.6
pp.327-337
June 2021
S.Santhosh
R.Rajasekar
V.K.Gobinath
C.Moganapriya
A.Manju Sri
95Experimental investigation on joining process of aluminium alloy 6063?T6 pipes using hybrid friction stir weldingJournal of the Brazilian Society of Mechanical Sciences and EngineeringInternationalVol.43, No.7
pp.331, June 2021
S.M.Senthil
S.Ragu Nathan
R.Parameshwaran
96Evaluation on strength parameters of self-compacting concrete incorporated with carbon and glass fibresMaterials today : ProceedingsInternationalVol.45, No.2
pp.708-712
June 2021
T.Jeevethaa
S.VijayaShanthy
A.Sivakumar
N.BagathSingh
97Ergonomic evaluation of ergonomically designed chalkboard erasers on shoulder and hand-arm muscle activity among college professorsInternational Journal of Industrial EngineeringInternationalVol.84, No.103170
p.44440
June 2021
S.Shankar
R.Naveen Kumar
S.Janaki Raman
CPS.Hariharan
S.Karthik Raja
98Experimentational Analysis on Combustion, Performance and Emission Characteristics of An Internal Combustion Engine using BioalcoholsJournal of Environmental Protection and EcologyInternationalVol.22, No.2
pp.735-749
May 2021
S.Ajay
P.Somasundaram
99Parameter optimization of copper nanoparticle synthesis by electrodeposition process using RSM and CSMaterials Today: ProceedingsInternationalVol.45, No.2
pp.751-756
May 2021
A.Tamilvanan
K.Balamurugan
T.Mohanraj
P.Selvakumar
B.Madhankumar
100Carbon-based Multi-layered Films for Electronic Application: A ReviewJournal of Electronic MaterialsInternationalVol.50, No.4
pp.1845-1892
February 2021
RajasekarRathanasamy
SumantaSahoo
JoongHee Lee
Ashok Kumar Das
MahalakshmiSomasundaram
Sathish Kumar Palaniappan
SanthoshSivaraj
101Numerical and experimental investigation on the thermochemical gasifcation potential of Cocoa pod husk (TheobromaCacoa) in an open?core gasiferClean Technologies and Environmental PolicyInternationalVol.23, No.5
pp.1603-1615
February 2021
G.Arun Prasad
P.C.Murugan
P.SajiRaveendran
S.Joseph Sekhar
102Investigation on the yield of producer gas from tamarind shell (TamarindusIndica) as feedstock in an Imbert type biomass gasifierFuelInternationalVol.292, No.120310
pp.44440
January 2021
P.C.Murugan
S.Joseph Sekhar
103Experimental investigation of control parameters for machining of copper alloys using electrochemical micromachiningMaterials Today: ProceedingsInternationalVol.45, No.2
pp.2498-2500
May 2021
M.Makesh
G.Sivaraman
N.Saravanan
S.Prashanth
Ram Subbiah
K.Anand
104Optimization of Process Parameters of Ultrasonic Welding on Ddissimilar Metal JointsArchives of Metallurgy and MaterialsInternationalVol.66, No.3
pp.887-892
May 2021
A.Mohan Kumar
R.Rajasekar
V.Karthik
S.Kheawhom
105Effect of thrust force, torque, and induced temperature on Kevlar reinforced composites during drilling processMaterials today ProceedingsInternationalVol.45, pp.522-528
May 2021
A.Mohan kumar
R.Parameshwaran
R.Rajasekar
V.C.HarisshRagavendra
N.Praveenraj
106Investigation of mechanical behavior of palmyra palm petiole fiber reinforced epoxy compositesMaterials today proceedingsInternationalVol.45, pp.1417-1422
May 2021
A.Mohan Kumar
M.Gowthaman
M.Harikrishnan
A.Kesavananthanan
107Utilisation of vapour compression refrigeration system in a solar still – an experimental study on summer daysJournal of Environmental Protection and EcologyInternationalVol.22, No.2
pp.769-780
May 2021
N.Prasanna
P.Somasundaram
108Influence of Dual Filler Reinforcement on the Curing and Tribo-Mechanical Behaviour of Natural Rubber Nanocomposite for Tire Tread ApplicationArchives of Metallurgy and MaterialsInternationalVol.66, No.3
pp.893-899
May 2021
M.Harikrishna Kumar
S.Shankar
R.Rajasekar
Samir Kumar Pal
P.Sathish Kumar
109Comparative Study on Mechanical Performances of Circular and Flat Geometry Welds in Friction Stir Welding of Aluminium AlloyArchives of Metallurgy and MaterialsInternationalVol.66, No.3
pp.881-886
May 2021
S.M.Senthil
S.Ragu Nathan
R.Parameshwaran
110Development of concentrating dish and solar still assembly for sea water desalinationMaterials Today Proceedings InternationalVol.45, No.2
pp.974-980
May 2021
A.Abubakkar
P.Selvakumar
T.Rajagopal
A.Tamilvanan
111A Frontier Statistical Approach Towards Online Tool Condition Monitoring and Optimization for Dry Turning Operation of SAE 1015 SteelArchives of Metallurgy and MaterialsInternationalVol.66, No.3
pp.901- 909
May 2021
C.Moganapriya
R.Rajasekar
V.K.Gobinath
P.Prabhakaran
J.Saravana Kumar
112Performance assessment of hard coating on rock cutting bit and process parameter optimization through multi-response approach using DEAR-Taguchi techniqueArabian Journal of GeosciencesInternationalVol.14, No.11
pp.1-14
May 2021
P.Sathish Kumar
Samir Kumar Pal
C.Moganapriya
R.Rajasekar
113Technical performance of nano-layered CNC cutting tool inserts – An extensive reviewMaterials Today ProceedingsInternationalVol.45, No.2
pp.663-669
May 2021
C.Moganapriya
M.Vigneshwaran
G.Abbas
A.Ragavendran
V.C.HarisshRagavendra
R.Rajasekar
114Augmenting the performance of photovoltaic cell through surface coating of molybdenum disulphideChalcogenide LettersInternationalVol.18, No.4
pp.161-170
April 2021
S.Prashanth
R.Rajasekar
V.K.Gobinath
G.Raja
K.Subha
K.S.Manjunath
115Stress analysis of riveted and bolted joints using analytical and experimental approachMaterials today proceedingInternationalVol.42, No.2
pp.1091-1099
April 2021
K.V.Satheesh Kumar
P.Selvakumar
R.Jegadeeswari
M.Dharmaraj
116Performance Analysis of Ball Bearing with Solid Contamination using vibration AnalysisSpringerInternationalpp.175-182, April 2021K.A.Ibrahim sheriff
V.Hariharan
B.Varunesh
117Selection of appropriate reinforcement for nylon material through mechanical and damping characteristicsPolimerosInternationalVol.30, No.4
pp.1-8
April 2021
B.S.Hari
R.Rajasekar
M.Harikrishna Kumar
C.Moganapriya
V.K.Gobinath
N.Saravanan
118Investigation of mechanical and corrosion properties of Al 7075/Redmud metal matrix compositeRevista de MetalurgiaInternationalVol.57, No.1
pp.1-9
April 2021
M.Sambathkumar
K.S.K.Sasikumar
R.Gukendran
K.Dineshkumar
K.Ponappa
S.Harichandran
119Investigations of Antifriction bearing defects using Vibration Signatures IOP Conf. Series: Materials Science and EngineeringInternationalVol.1084, No.1
pp.1-14
April 2021
V.Hariharan
P.Thangavel
G.Rajeshkumar
D.Deepa
120Influence of Sodium Hydroxide (NaOH) Treatment on Mechanical Properties and Morphological Behaviour of Phoenix sp. Fiber/Epoxy CompositesJournal of Polymers and the EnvironmentInternationalVol.29, No.3
pp.65-74
April 2021
G.Rajeshkumar
V.Hariharan
S.Indran
M.R.Sanjay
SuchartSiengchin
J.Prakash Maran
Naif Abdullah Al Dhabi
Ponmurugan Karuppiah
121Improve the efficiency of Battery Cooling System in E Vehicle by Nanofluids with CFD AnalysisIOP Conf.Series : Materials Science and EngineeringInternationalVol.1126, No.1
pp.1-12
April 2021
H.Vinoth Kumar
S.Saravanakumar
A.Sivakumar
122CFD study on the performance of reducing pressure drop holes in cyclone separatorMaterials Today ProceedingsInternationalVol.43, No.2
pp.1960-1968
April 2021
N.Prasanna
S.Karthikeyan
S.Ajay
T.Rajagopal
V.Vigneshwaran
123A Critical Review on Fume Extraction System for Pipe and Plate WeldingIOP Conf. Series: Materials Science and EngineeringInternationalVol.1084
No.012064
pp.1-14
March 2021
K.V.Satheesh Kumar
M.Dharmaraj
P.Thangavel
K.A.Srikishore
R.Sudharsan
M.Vimal
124Enhancing the Free Vibration Characteristics of Epoxy Polymers Using Sustainable Phoenix Sp. Fibers and Nano-Clay for Machine Tool ApplicationsJournal of natural fibersInternationalVol.18, No.4
pp.531–538
March 2021
G.Rajesh Kumar
V.Hariharan
S.S.Saravanakumar
125Simulation of 1.2765 DIN steel billet and crack analysis during the forging process using DEFORM 3D softwareMaterialwissenschaft und WerkstofftechnikInternationalVol.52, No.3
pp.332-338
March 2021
A.Mohan Kumar
R.Parameshwaran
R.Rajasekar
126Experimental Investigation of Tensile Strength and Hardness in GMAW/GTAW Butt Welded Joints with Various Shielding Gas CompositionsLecture Notes in Mechanical EngineeringInternationalpp. 57-78, March 2021K.V.Satheesh Kumar
K.A.Srikishore
A.Shek Mohammed Asiq
R.Sudharsan
127Investigation on the effect of technological Parameters on emission factor In 316l stainless steel using gas metal arc WeldingArchives of Metallurgy and MaterialsInternationalVol.66, No.2
pp.609-615
March 2021
K.V.SatheeshKumr
P.Selvakumar
K.R.UvanShankar
S.Thirunavukarasu
V.Vijay Anand
D.Vishal
128Energy Conservation on Vapour Compression Refrigeration System using PCMIOP Conf. Series: Materials Science and EngineeringInternationalVol.1048, pp.012106
March 2021
P.SajiRaveendran
P.C.Murugan
129Dynamic Mechanical Properties and Free Vibration Characteristics of Surface Modified Jute Fiber/Nano-Clay Reinforced Epoxy CompositesJournal of Polymers and the EnvironmentInternationalVol.29, pp.1076-1088
March 2021
S.Ramakrishnan
K.Krishnamurthy
G.Rajeshkumar
M.Asim
130Experimental Analysis of Tribological Behaviour of Jute Fiber-Reinforced Nanoclay Filled Epoxy CompositesLecture Notes in Mechanical EngineeringInternationalpp.1-14, March 2021S.Ramakrishnan
K.Krishnamurthy
G.Rajeshkumar
131Comparison of MA-g-PP effectiveness through mechanical performance of functionalised graphene reinforced polypropylenePolimerosInternationalVol.30, No.3
pp.e2020035
March 2021
N.Saravanan
R.Rajasekar
P.Sathish Kumar
V.Suresh
B.S.Hari
Kaushik Pal
132Measurement of Drag Force Acting on a Linke Hofmann Busch Design Railway Coach Through Wind Tunnel TestingJ. Inst. Eng. India Ser. CInternationalVol.102, No.1
pp.145-155
March 2021
A.Abubakkar
T.Murugan
133Vibration analysis of nylon gear box utilizing statistical methodMaterials Today: ProceedingsInternationalVol.33, No.7
pp.3525-3531
March 2021
C.Poongodi
B.S.Hari
S.Arunkumar
134Influence of graphene oxide on the morphological and mechanical behaviour of compatibilized low density polyethylene nanocompositesMaterials today proceedingsInternationalVol.39, No.4
pp.1487-1493
March 2021
B.S.Hari
K.V.Mahesh Kumar
K.Krishnamurthy
P.Sathish Kumar
V.K.Gobinath
R.Sachinbala
R.Rajasekar
135Experimental Studies on the Application of Biomass Gasifier for Drying Tapioca in Remote AreasIOP Conf. Series: Materials Science and EngineeringInternationalVol.1084, pp.1-7
March 2021
P.C.Murugan
P.SajiRaveendran
136Mechanical strength retention and service life of Kevlar fiber woven mat reinforced epoxy laminated composites for structural applicationsPolymer CompositesInternationalVol.42, No.4
pp.1855-1866
March 2021
T.P.Sathishkumar
M.Muralidharan
S.Ramakrishnan
M.R.Sanjay
SuchartSiengchin
137Achieving machining effectiveness for AISI 1015 structural steel through coated inserts and grey-fuzzy coupled Taguchi optimization approachStructural and Multidisciplinary OptimizationInternationalVol.63, No.3
pp.1169-1186
March 2021
C.Moganapriya
R.Rajasekar
P.Sathish Kumar
T.Mohanraj
V.K.Gobinath
J.Saravanakumar
138Improve the efficency of battery Cooling Sytem in E Vehicle by nano-fluids with CFD AnalysisIOP Material Science and EngineeringInternationalVol.1126, No.63
pp.1-12
March 2021
H.Vinothkumar
S.Saravanakumar
A.Sivakumar
139Investigation on the yield of producer gas from tamarind shell (TamarindusIndica) as feedstock in an Imbert type biomass gasifierFuelInternationalVol.292, No.120310
pp.1-9
February 2021
P.C.Murugan
S.Joseph Sekhar
140An experimental investigation on utilizing cassava stalk as biomass sources in a gasifierIOP Conf. Series: Materials Science and EngineeringInternationalVol.1057, No.012040
pp.1-8
February 2021
P.C.Murugan
P.Navaneethakrishnan
S.Joseph Sekhar
141Experimental Evidence on enhancing equipment effectiveness with the implementation of TPM Principles in the Bus body Building IndustryTierarrztliche PraxisInternationalVol.40, pp.2429-2442
February 2021
N.Bagathe Singh
A.Sivakumar
142Experimental studies on micro-channel heat sink with different heat transfer fluidAIP Conference ProceedingsInternationalVol.2317, No.030019
pp.1-16
February 2021
M.P.Dhanish
P.Selvakumar
V.Ashwin
P.N.ArunKumar
143Manufacturing methods of healthy and edible cups- An integrative reviewIOP Conf. Series: Materials Science and EngineeringInternationalVol.1055, No.012017
pp.1-20
February 2021
K.V.Satheeshkumar
S.Vikram
S.J.Vigneswaran
C.T.A.Sudhanhari
144Exergy analysis of forced convection solar flat plate collector using different working fluidsIOP Conf. Series: Materials Science and EngineeringInternationalVol.1055, No.012014
pp.1-7
February 2021
T.Rajagopal
N.Prasanna
S.Ajay
A.Yazharasu
K.Aranganathan
145Effect of relative content on mechanical properties of coir and Napier grass fibers reinforced hybrid polyester compositesMaterials Today ProceedingsInternationalVol.33, No.7
pp.2929-2933
February 2021
S.Karthi
K.S.K.Sasikumar
R.K.Sangeetha
N.Saravanan
146Heat Transfer Augmentation Using Water-in-Glass Evacuated Tube Coupled with Parabolic Trough in Rack Dryer in the Drying of Capsicum FrutescensInternational Journal of Heat and TechnologyInternationalVol.38, No.4
pp.895-902
January 2021
S.Pandiaraj
T.Ayyasamy
K.Govindasamy
147Experimental and numerical analysis of impact strength of Al6082 for automotive structural applicationsMaterials Today ProceedingsInternationalVol.33, No.7
pp.2863-2867
January 2021
D.Karupannasamy
K.SasiKumar
S.Shankar
148Mechanical and fracture study of hybrid natural fiber reinforced composite–Coir and sugarcane leaf sheathMaterials Today ProceedingsInternationalVol.33, No.7
pp.2795-2797
January 2021
M.Arul
K.Sasikumar
M.Sambathkumar
R.Gukendran
N.Saravanan
149Waste water treatment process using Nano TiO2Materials Today ProceedingsInternationalVol.33, No.7
pp.2570-2572
January 2021
N.Saravanan
K.Sasikumar
150Investigations on AWJ cutting process of hybrid aluminium 7075 metal matrix composites using nozzle oscillation techniqueMaterials Today ProceedingsInternationalVol.33, No.7
pp.2798-2802
January 2021
N.Nandakumar
K.Sasikumar
M.Sambathkumar
N.Saravanan
151Effect of shot peening on surface properties of Al7075 hybrid aluminum metal matrix compositesMaterials Today ProceedingsInternationalVol.33, No.7
pp.2792-2794
January 2021
K.Sasikumar
K.Dineshkumar
K.Deeban
M.Sambathkumar
N.Saravanan
152Acoustic characterization of farm residues for sound absorption applicationsMaterials Today ProceedingsInternationalVol.33, No.7
pp.2917-2922
January 2021
K.Sasikumar
N.Saravanan
M.Sambathkumar
R.Guekndran
153Semi automated grain and copra collector. International journal of mechanical and production engineering research and developmentInternational Journal of Mechanical and Production Engineering Research and DevelopmentInternationalVol.10, No.3
pp.663-668
December 2020
B.S.Hari
S.Barath
S.Arunkumar
J.Abiram
154Emission Control and Reduction in Fuel consumption of Two-Stroke SI Engineusing Nano-Fragment as a CatalystAIP Conference ProceedingsInternationalVol.2311, No.1
pp.0400071-0400078
December 2020
S.Karthikeyan
A.P.SathiyaGnanam
D.Damodharan
N.Prasanna
N.Mukilarasan
155Dynamic Mechanical Properties and Free Vibration Characteristics of Surface Modified Jute Fiber/Nano-Clay Reinforced Epoxy CompositesJournal of Polymers and the EnvironmentInternationalpp.1-13, December 2020S.Ramakrishnan
K.Krishnamurthy
G.Rajeshkumar
M.Asim
156Experimental investigation on tribological characeteristics of NaOH treated chopped abaca fiber reinforced expoxy compositesMaterials Science ForumInternationalVol.1019, pp.25-31
December 2020
Rittin Abraham Kurien
D Philip Selvraj
M.Sekar
R.Rajasekar
Chacko Preno Koshy
157Performance Evaluation of Domestic Refrigerator with Waste Heat Recovery SystemIOP Conf. Series: Materials Science and EngineeringInternationalVol.995, pp.1-8
December 2020
P.Thangavel
S.Mokesh
S.A.Reavanth
K.Pragatheeswaran
158Performance Evaluation of Portable Mist HumidifierIOP Conference Series: Materials Science and EngineeringInternationalVol.995, No.012030
pp.1-7
December 2020
M.Mahesh
P.Thangavel
K.Bhuvaneshwaran
V.Boopathi Raja
S.Dinaesh Krishna
159Soil monitoring and Analysis with IoTJournal of Xidian UniversityInternationalVol.14, No.12
pp.208-217
December 2020
D.Deepa
C.Poongodi
P.Thangavel
160Soil type detection in a land area from satellite images using remote sensing conceptInternational Journal of Interdisciplinary Global StudiesInternationalVol.14, No.4
pp.237-241
December 2020
D.Deepa
C.Poongodi
T.Perarasi
P.Thangavel
161Performance Analysis of Cold Energy Storage using Phase Change MaterialIOP Conference Series: Materials Science and EngineeringInternationalVol.995, No.012031
pp.1-11
December 2020
R.Karthikeyan
P.Thangavel
162Analysis of lean manufacturing layout in a textile industryMaterials Today ProceedingsInternationalVol.33 pp.3486-3490
December 2020
A.Sivakumar
H.VinothKumar
N.Bagathsingh
163Process and analysis with demographic methodological refinement of bus body industryMaterials Today ProceedingsInternationalVol.33, pp.3549-3557
December 2020
A.Sivakumar
N.Bagathsingh
H.VinothKumar
S.Saravanakumar
164Influencing Parameters of productivity through value stream analysis using optimization techniquesMaterials Today ProceedingsInternationalVol.33, pp.3591-3599
December 2020
A.Sivakumar
165Performance analysis on Solar Air Heater with Discrete Arc Shaped Rib Element in Absorber PlateIOP Conference Series: Materials Science and EngineeringInternationalVol.995, No.012032
pp.1-6
December 2020
M.Makeshkumar
P.Thangavel
166Study on mechanical behavior of jute matrix composite with fly-ash fillerJournal of Seybold ReportInternationalVol.15, No.9
pp.730-735, 2020
R.Gukendran
M.Sambathkumar
K.S.K. Sasikumar
167Study of al 7075 fluidity by spiral fluidity test equipmentJournal of Seybold ReportInternationalVol.15, No.9
pp.711-717, 2020
M.Sambathkumar
K.S.K.Sasikumar
R.Gukendran
M.Paramasivam
168Enactment of Conventional Machine Learning Algorithms for Predicting CFBC Cyclone Separator PerformanceInternational Journal of Emerging Trends in Engineering ResearchInternationalVol.8, No.8
pp.4102-4111, 2020
M.Vijayakumar
S.Karthikeyan
N.Prasanna
S.Ajay
169Analysis of Performance using IDE Frame Work International Journal of Emerging Trends in Engineering ResearchInternationalVol.8, No.8
pp.4112-4117, 2020
M.Vijayakumar
N.Prasanna
M.Kishanth
170Analysis of Grinder, Frame and Rotavator Blade in Cowdung Spreader International Journal of Advanced Science and TechnologyInternationalVol.29, No.3
pp.14236-14257, 2020
K.V.Satheesh Kumar
K.K.Sabarikanth
N.Monish
P.Prakash
171 A Ergonomic Factors Analyzing of Pressing Workstation with RULAHigh Technology LettersInternationalVol.26, No.9
pp.720-728, 2020
H.Vinothkumar
A.Sivakumar
172Engine Combustion Test using Algae Biofuel with Nanofluid Journal of Scientific & Industrial ResearchInternationalVol.79, pp.854-857
September 2020
N.Saravanan
KSK.Sasikumar
173Machining Fixture Layout Optimization Using Symbiotic Organisms Search Algorithm, Tierärztliche Praxis,InternationalVol.40, pp.1286-1295, 2020P.Praveen
S.Selvakumar
K.M.Arunraja
174Investigation of wear resistance and mechanical properties of CNT reinforced aluminium 7075 alloy for gear applicationsInternational journal of scientific & technology researchInternationalVol.9, No.6 pp.446-454, 2020K.Manikandan
S.Jeeva
V.Gokul Santhosh
K.Gokul
175Exergy Analysis of Ideal Otto Cycle with Oxy-Fuel and Exhaust Gas RecirculationResearch Journal of Chemistry and EnvironmentInternationalVol.24, pp.79-84, 2020T.Rajagopal
A.Yazharasu
U.Karthick
176A Review on Elements of Schedule Management Planning and their use in Project ManagementJournal of Seybold reportInternationalVol.25, No.10 pp.191-199, 2020D.Suresh
A.Sivakumar
177Experimental studies on the performance improvement of household refrigerator connected to domestic water system with a water-cooled condenser in tropical regionsApplied Thermal Engineering InternationalVol.179, Article ID:115684
October 2020
P.Saji Raveendran
S.Joseph Sekhar
178Finding the performance and emission characteristics of a nanoparticles added castor oil biodiesel blends in a CI engineEuropean Journal of Molecular & Clinical MedicineInternationalVol.7, No.2 pp.3313-3323, 2020Milind Shivaji Rohokale
Gujar Anantkumar Jotiram
Nasim Hasan
Ajay Sukumaran
Shafali Jain
179Reactive compatibilization effect of graphene oxide reinforced butyl rubber nanocompositesPolímerosInternationalVol.30, No.3, 2020C.Sathishranganathan
R.Rajasekar
M.Harikrishna Kumar
J.Prakash Maran
P.Sathish Kumar
Samir Kumar Pal
180Experimental studies on the performance improvement of household refrigerator connected to domestic water system with a water-cooled condenser in tropical regionsApplied Thermal Engineering InternationalVol.179, Article ID: 115684, 2020P.Saji Raveendran
S.Joseph Sekhar
181Decanol proportional effect prediction model as additive in palm biodiesel using ANN and RSM technique for diesel engineEnergyInternationalVol.213, pp.119072, 2020A.Naresh Kumar
P.S.Kishore
K.Brahma Raju
B.Ashok
R.Vignesh
AK.Jeevanantham
K.Nanthagopal
A.Tamilvanan
182Fault diagnosis of unbalanced multirotor systems Springer Lecture Notes in Mechanical Engineering InternationalProceedings of ICIME 2020 pp.387-396, 2020V.Hariharan
G.Rajeshkumar
K.A.Ibrahim Sheriff
183Fabrication and characterization of AA7075 reinforced with ticp compositesSolid state technology InternationalVol.63, No.6
pp.6289-6300, 2020
S.Manikandan
K.Deepandurai
184Offshore integrated renewable power system IOP conference series : Materials science and engineering InternationalVol.955, Article ID:012074, 2020K.Deepandurai
P.Arun Prasath
P.Ajith kumar
M.Deepak
185Multi-functional fuel additive as a combustion catalyst for diesel and biodiesel in CI engine characteristicsFuelInternationalVol.278, No.15
pp. 1-13
October 2020
A.TAmilvannan
B.Ashok
K.Nanthagopal
Ong Hwai Chyuan
Phung Thi Kim Le
Kedar khanolkar
Ninad Raje
Arun Raj
V.Karthickey
186Design and Fabrication of Raisin Dryer using Solar Powered Air BlowerInternational Journal of Recent Technology and EngineeringInternationalVol.9, No.2
pp.136-138
July 2020
A.Saravanan
S.Kishore
A.Gowtham
S.Mathan
187Experimental study on thermal behavior of double pipe helical flow heat exchangerIOP Conference Series: Materials Science and EngineeringInternationalVol.764, pp.012050, 2020P.Praveen
R.Karthikeyan
R.Naveen
P.Selvakumar
S.Astra
188Fume Formation Rates in Welding- A Comprehensive ReviewInternational Journal of Advanced Science and TechnologyInternationalVol.29, No.6
pp. 6449 - 6459, 2020
K.V.Satheeshkumar
S.Surya
M.Vedhasagara
S.A.Srikishore
S.Vikram
189Performance enhancement of Solar flat plate collectorsResearch Journal of Chemistry and EnvironmentInternationalVol.24, No.1
pp.75-78, 2020
A.Abubakar
T.Rajagopal
S.Vikram
C.Sridhar
190An Experimental and Numerical Study on The Performance of Downdraft Gasifier With Blends Of BiomassInternational Journal of Scientific &Technology ResearchInternationalVol.9, No.6, June 2020P.C.Murugan
V.Vel Kumara Samy
T.Vishnu Bharathi
M.Surya Parkash
191Exergy Analysis of Ideal Otto Cycle with Oxy-Fuel and Exhaust Gas RecirculationResearch Journal of Chemistry and EnvironmentInternationalVol.24, No.1 pp.79-84, 2020T.Rajagopal
A.Yazharasu
U.Karthick
192Micro Structural Observations of Magnesium Oxide and Titanium Di-Oxide Hybrid Solar Cell by FESEMInternational Journal of Advanced Science and TechnologyInternationalVol.29, No.5
pp.12305-12314, 2020
K.Kathirvel
G.Bharath
O.P.Shri Ram
V.Srikanth
R.V.Vasanth
193Performance Analysis of Vapour Absorption Refrigeration System using Waste Heat from IC EngineInternational Journal of Advanced Science and TechnologyInternationalVol.29, No.5
pp.10879-10892, 2020
P.Praveen
S.Santhosh
R.Raaghul
A.S.Pramoth Kumar
194CFD Analysis on Nozzle Inclinations in Forced Air Cooling System for IndustriesInternational Journal of Advanced Science and TechnologyInternationalVol.29, No.3
pp.9670-9691, 2020
K.V.Satheesh Kumar
M.Dharmaraj
M.Udhayan
M.R.Surya
M.Vedhasagaran
195Experimental studies on the performance improvement of household refrigerator connected to domestic water system with a water-cooled condenser in tropical regionsApplied Thermal EngineeringInternationalVol.179, pp.1-8, 2020P.Saji Raveendran
S.Joseph Sekhar
196Measurement of Drag force acting on a Linke Hofmann Busch Design Railway  coach through Wind Tunnel testingJj  Journal of the Institution of Engineers (India ): Series CInternationalVol.29, No.3 pp.9670-9691, 2020A.Abubakkar
T.Murugan
197Investigation of wear resistance and mechanical properties of CNT reinforced aluminium 7075 alloy for gear applicationsInternational journal of scientific & technology researchInternationalVol.9, No.6
pp.446-454, 2020
K.Manikandan
V.Gokul Santhosh
K.Gokul
198A multi-objective optimization of the friction stir welding process using RSM-based-desirability function approach for joining aluminum alloy 6063-T6 pipesSStructural and Multidisciplinary OptimizationInternationalVol.62, No.3
pp.1-17, 2020
S.M.Senthil
R.Parameshwaran
S.R.Nathan
M.B.Kumar
K.Deepandurai
199Design and Fabrication of Mint Plucker using Cam MechanismInternational journal of scientific & technology researchInternationalVol.9, No.1
pp.1309-1313, 2020
M.Sambath Kumar
S.Shanmugavel
A.R.Surean
S.Srinivasan
200Influence of Milling Parameters on Surface Roughness of Al–SiC–B4C CompositesTransactionof Indian Institute of MetalsInternationalVol.73, pp.1171–1183, 2020M.B.Kumar
R.Parameshwaran
K.Deepandurai
201Experimental Study on Thermal Behaviour of Double Pipe Helical Flow Heat ExchangerMaterials Science and EngineeringInternationalVol.764, No.1
pp.012050, 2020
R.Karthikeyan
P.Thangavel
R.Naveen
P.Selvakumar
S.Astra
202Influence of Prosopis Juliflora wood flour in Poly Lactic Acid–Developing a novel Bio-Wood Plastic Composite.PolímerosInternationalVol.30, No.1, 2020S.S.Raj
T.K.Kannan
R.Rajasekar
203An Extended Approach on Power Conversion Efficiency Enhancement through Deposition of ZnS-Al2S3 Blends on Silicon Solar CellsJournal of Electronic MaterialsInternationalVol.49, pp.5937–5946, 2020G.V.Kaliyannan
S.V.Palanisamy
R.Rathanasamy
M.Palanisamy
N.Nagarajan
S.Sivaraj
M.S.Anbupalani
204Semi Automated Grain and Copra CollectorInternational Journal of Mechanical and Production Engineering Research and DevelopmentInternationalVol.10, No.3
pp.663-668
June 2020
B.S.Hari
S.Barath
S.Arun kumar
J.T.Abiram
205Substantial reduction of carbon black and balancing the technical properties of styrene butadiene rubber compounds using nanoclayJournal of Rubber ResearchInternationalVol.23, pp.79–87
May 2020
M.Harikrishnakumar
S.Shankar
R.Rajasekar
Samir Kumar Pal
P.Sathish Kumar
206Implementation of fuzzy-based integrated framework for sesame seed separator developmentSoft Computing InternationalVol.24
pp.7715-7734
May 2020
C.Baskar
R.Parameshwaran
N.Nithyavathy
207Design and Development of Jackfruit Bulbs Extractor Stage-I International Journal of Advanced Science and TechnologyInternationalVol.29, No.9
pp.2006-2015
2020
N.Prasanna
S.Ajay
S.Karthikeyan
M.Gowrishankar
208Performance Analysis of Cascade Refrigeration System with Alternate Performance RefrigerantsInternational Journal of Emerging Trends in Engineering ResearchInternationalVol.8, No.5
pp.2047-2054
May 2020
M.Mahesh
P.Thangavel
K.Bhuvaneshwaran
V.Boopathi Raja
M.Gajini Mohammed
K.S.GiriePrashath
209Performance Improvement of VCRS using Waste Heat Recovery Method International Journal of Emerging Trends in Engineering Research InternationalVol.8, No.5
pp.1964-1971
May 2020
M.Mahesh
P.Thangavel
B.Arulpriyan
M.S.Abdullah
P.Gokul
210Explicit dynamic analysis of industrial helmet manufactured using bamboo and vakka fiber composites International Journal of Emerging Trends in Engineering Research InternationalVol.8, No.5
pp.2165-2168
May 2020
A.Somasundaram
B.Anish Kumar
B.Ashok
211Performance Analysis of Solar Box CookerInternational Journal of Engineering Research & TechnologyInternationalVol.9, No.4
pp.317-320
April 2020
T.Ravisankar
K.Dinesh
S.Angappan
K.Dharmaraj
212Design of lean burn engine for scootersInternational Journal of Recent Technology And EngineeringInternationalVol.8, No.6
pp.2076-2080
March 2020
S.Dhamotharan
S.Selvakumar
K.Kathirvel
M.Sivaraman
G.Bharath
213Design and fabrication of manure spreaderInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.3
pp.5134-5136
March 2020
P.Sathiamurthi
A.S.Anaamalaai
M.R.AhamedBuhari
A.Anburaja
M.AjmalThahasin
214Concentrated Solar Cooker By Integrating PCM MaterialInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.737-739
February 2020
S.Selvakumar
S.Arun Santhosh
V.Dinesh Kumar
K.Gokulakrishnan
215Design and Fabrication of Portable Shuttlecock and Tennis Ball Shooting (Training) MachineInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.1093-1095
February 2020
K.Deepandurai
S.Abishek
N.Devanandh
S.Dineshkumar
216Design and Fabrication of Zig-Zag Rod Folding Machine for Pre-Casted Beam used for Roofing ConstructionInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.4966-4969
February 2020
K.Deepandurai
T.Enith
D.Bharanidharan
K.Arun Kumar
217Midget Salt Spray Testing Machine for Rapid Corrosion TestInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.462-465
February 2020
R.Kamalakannan
B.Arunkumar
S.Arun kumar
C.Bhavishnu
218Review on Condition Monitoring of Rotating MachinesInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.2343-2346
February 2020
K.A.Ibrahim Sheriff
V.Hariharan
B.Mathan Kumar
219Grain CollectorInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.4987-4990
February 2020
A.Saravanan
V.MohanaselvanR.Mohan
B.Mohan Prasad
220Fabrication of Floor Scrubber MachineInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.2251-2253
February 2020
N.Saravanan
S.Sanjay
R.S.Sreenithiyanandan
T.Vimal Raj
221Manure Removal System using Lead Screw MechanismInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp. 868-871
February 2020
R.Karthikeyan
R.Bhubesh
M.Ezhil Kumaran
S.S.Deivavijay
222Non destructive testing and evaluation of friction stir welded AA6063 circularly butted pipesRussian Journal of Non Destructive TestingInternationalVol.55, No.12
pp.957-966
February 2020
S.M.Senthil
R.Parameshwaran
S.Ragunathan
S.Karthi
223Automatic Urinal Flushing using Hydraulic System: Hygienic ToiletsInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.5849-5852
February 2020
M.Harikrishna Kumar
S.Prasanth
A.Prassanth
M.Praveen Kumar
224Turmeric Harvester for traditional and mechanized way of cultivationInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.5769-5772
February 2020
P.Prabhakaran
D.Nithiyanantham
S.Naveen
P.Prakash
D.Vishal
225Design And Fabrication of Small Scale Sugarcane Harvesting MachineInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.6458-6460
February 2020
K.Paramasivam
R.Sankara Narayanan
G.RanjithKumar
P.Prawinkumar
226Performance Enhancement in Solar Flat Plate CollectorInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.2558-2562
February 2020
T.Rajagopal
K.Aranganathan
R.V.Arun kumar
M.Boobalan
227Design and Fabrication of Agricultural Land Tilling and Planting MachineInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.4970-4974
February 2020
P.Selvakumar
M.Dhanishk
V.Ashwin
P.N.Arun Kumar
228Design and Fabrication of Frosty Bike Seat CoverInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.2
pp.4980-4983
February 2020
A.Mohan Kumar
M.Gowthaman
M.Harikrishnan
A.Kesava nanthanan
229Design and Fabrication of Experimental Setup for Detecting and Analyzing the Defect in Solar PanelInternational Journal of Innovative Technology and Exploring Engineering InternationalVol.9, No.4
pp.2451-2454
February 2020
K.A.Ibrahim Sheriff
V.Vijay Prasanna
S.Varun
V.Vinoth
230Design analysis and Investigation of Fabricated Weeder for TapiocafarmInternational Journal of Mechanical Engineering and TechnologyInternationalVol.11, No.2
pp.81-91
February 2020
A.Sivakumar

P.Manivel
R.Justin Prakasam
G.M.Kishore
S.Karunakaran
231Design and Fabrication of Paper Pot TransplanterInternational Journal of Scientific and Technology ResearchInternationalVol.9, No.1
pp.1319-1322
January 2020
M.Dharmaraj
K.M.Mounesh
R.Poovarasan
R.Rahul
232Design and Fabrication of Irrigation Canal RenovatorInternational Journal of Scientific and Technology ResearchInternationalVol.9, No.1
pp.1323-1326
January 2020
S.M.Senthil
K.B.Vishnu Prasanth
S.Ramnivas
E.Manikandan
233Design and Fabrication of Triple Pipe Heat Exchanger with Spiral Twisted TapeInternational Journal of Scientific and Technology ResearchInternationalVol.9, No.1
pp.4339-4343
January 2020
K.A.Ibrahim Sheriff
S.V.Pradeep
S.Neethivendhan
S.Praveen Kumar
234Design and Fabrication of Mint Plucker Using Cam MechanismInternational Journal of Scientific and Technology ResearchInternationalVol.9, No.1
pp.1309-1313
January 2020
M.Sambath Kumar
S.Shanmugavel
A.R.Surean
S.Srinivasan
235Evaluation of Shoulder Pain Among the Workers Involved in Ironing Process Using Surface ElectromyographyJournal of Medical Imaging and Health InformaticsInternationalVol.10, No.1
pp.86-92
January 2020
M.Vijay Anand
K.C.K.Vijayakumar
T.Mohanraj
236Biodegradable Tomato Plant Seedling Trays Made from Tapioca WasteInternational Journal of Scientific and Technology ResearchInternationalVol.9, No.1
pp.3745-3748
January 2020
P.Praveen
S.Santhosh
R.Raaghul
A.S.Pramothkumar
237Robust design of readymade Tea-maker machineInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.1
pp.3292-3296
January 2020
S.Ajay
N.Prassanna
S.Surya
S.Vasanth Kumar
S.Shri Krishna
238Cricket bat knocking machineInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.1
pp.3117-3124
January 2020
S.Naveenkumar
S.Janakiraman
C.P.S.Hariharan
S.Karthik Raja
239Design and fabrication of water saving utensils cleaning machineInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.1
pp.2665-2667
January 2020
P.Selvakumar
A.Angusamy
R.Anudeep
R.Ashok
240Design and Fabrication of Machine for Removal of Salt Formation in Borewell PipelineInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.1
pp.2619-2622
January 2020
R.Manivannan
R.Rajasekar
M.K.Maheswaran
S.Jegatheeshwaran
K.V.Kishore
241Design and Fabrication of Synthetic Sea Water ApparatusInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.1
pp.2635-2638
January 2020
R Kamalakannan
K.Sudharsan
K.Vignesh
S.Sujith Kumar
242Influence of ultrathin gahnite anti-reflection coating on the power conversion efficiency of polycrystalline silicon solar cellJournal of Materials Science: Materials in ElectronicsInternationalVol.31, No.3
pp.2308-2319
January 2020
P.Senthil Velmurugan
V.K.Gobinath
R.Rajasekar
P.Manivasakan
P.Sathish Kumar
C.Moganapriya
243Experimental Examination of Booster Heating Coil in Foodstuff Display CabinetInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.1
pp.1353-1359
January 2020
P.Navaneethakrishnan
PSS.Srinivasan
244Design and Fabrication of Rope Elevator for WorkersInternational Journal of Scientific & Technology ResearchInternationalVol.9, No.1
pp.2623-2626
January 2020
T.Ravisankar
S.Angappan
K.Dinesh
K.Dharmaraj
245Locomotive Lifter for Parking in Congested PlacesInternational Journal of Engineering and Advanced TechnologyInternationalVol.9, No.2
pp. 758-760
December 2019
A.Tamilvanan
K.Sampath Kumar
K.B.Sanjaya Krishnan
D.Saravana Kumar
246Design and Fabrication of Shoe Cleaning Cum Polishing MachineInternational Journal of Engineering and Advanced TechnologyInternationalVol.9, No.2
pp.5305-5308
December 2019
N.Baskaran
R.Sachinbala
K.Rohan
P.Logesh
247Design and Fabrication of Tamarind Seed Removal MachineInternational Journal of Scientific and Technology ResearchInternationalVol.8, No.12
pp.743-746
December 2019
R.Karthikeyan
B.E.Nirmal
M.Pravin Kumar
N.K.Pavithran
248Automated Pottery Wheel for the Village Community to Manufacture Earthern PotsInternational Journal of Scientific & Technology Research InternationalVol.8, No.12
pp.3042-3044
December 2019
P.C.Murugan
V.Tamilarasu
N.P.Tharani Dharan
R.S.Sreenithiyanandan
S.Vivek Raj
249Automatic Leaf Collector and Chopper for the Greenery LawnInternational Journal of Scientific & Technology ResearchInternationalVol.8, No.12
pp.3038-3041
December 2019
P.C.Murugan
V.Vel Kumara Samy
S.Vijaya Prasath
T.Vishnu Bharathi
250Design and Fabrication of Chairless ChairInternational Journal of Innovative Technology and Exploring Engineering InternationalVol.9, No.2
pp.103-107
December 2019
C.Sathishranganathan
G.Santhosh kumar
P.S.Prakash
J.G.Prabakaran
251Design and Development of Roadside Waste CollectorInternational Journal of Engineering and Advanced TechnologyInternationalVol.9, No.2
pp.1816-1819
December 2019
R.Manivannan
R.Rajasekar
S.Nithish Vetrivel
A.PraveenKumar
K.S.Nithesh Kumar
252Optimization of welding ficture layout for sheet metal components using DOEInternational Journal of Productivity and quality managementInternationalVol.28, No.4
pp.522-558
December 2019
K.M.Arunraja
S.Selvakumar
P.Praveen
253Improvement of product quality through optimum ficture design using DOE and FEMInternational Journal of recent Technology and Engineering InternationalVol.8, No.4
pp.2364-2369
November 2019
K.M.Arunraja
S.Selvakumar
P.Praveen
254Enhancement open circuit voltage of calcium titanate AR coated magnesium solar cellInternational Journal of Recent Technology and EngineeringInternationalVol.8, No.4
pp.1272-1278
November 2019
K.Kathirvel
S.Selvakumar
S.Dhamotharan
G.Bharath
M.Sivaraman
255Multi-objective optimization of edm process parameters for machining of hybrid aluminum metal matrix composites (Al7075/TiC/B4C) using genetic algorithmSurface Review and Letters (SRL)InternationalVol.26, No.10
pp.1-16
November 2019
K.Ponappa
KSK.Sasikumar
M.Sambathkumar
M.Udhayakumar
256Process Parameter Optimization in Green Sand Casting Using ANNInternational Journal Of Scientific & Technology ResearchInternationalVol.8, No.11
pp.2745-2748
November 2019
KSK.Sasikumar
R.Gukendran
R.Parameshwaran
M.Sambathkumar
257Influence of graphene oxide on the static and dynamic mechanical behavior of compatibilized polypropylene nanocompositesMaterials TestingInternationalVol.61, No.10
pp.986-990
October 2019
K.V.Mahesh Kumar
K.Krishnamurthy
R.Rajasekar
P.Sathish Kumar
Kaushik Pal
G.C.Nayak
258Impact of schedule management plan on project managament effectivenessInternational Journal of Engineering and Advanced TechnologyInternationalVol.9, No.1
pp.3350-3355
October 2019
D.Suresh
A.Sivakumar
259Design, Fabrication and Testing of Prototype of an Anti-Hypothermic Flexible Body HeaterInternational Journal of Scientific & Technology ResearchInternationalVol.8, No.10
pp.1596
October 2019
P.Selvakumar
A.Abubakkar
A.Tamilvanan
T.Rajagopal
260Natural Bio-Filters For Eco-Friendly Cleaning And Enrichment Of Producer GasInternational Journal of Scientific & Technology Research InternationalVol.8, No.10
pp.277-280
October 2019
G.Arun Prasad
P.C.Murugan
P.Praveen
P.Saji Raveendran
Godwin Glivin
261Welding Behaviour of Graphene Oxide Reinforced High Density Polyethylene NanocompositesInternational Journal of Engineering and Advanced Technology (IJEAT)InternationalVol.9, No.1
pp.3211-3215
October 2019
R.Manivannan
C.Moganapriya
A.Mohankumar
R.Rajasekar
G.C.Varun Kumar
262Investigations on micro hardness, electrical and thermal conductivity of AA7075 surface hybrid composites produced through friction stir processingMaterials Research ExpressInternationalVol.6, No.11
pp.1-17
October 2019
K.Suganeswaran
R.Parameshwaran
P.Thangavel
N.NithyavathyT.Sivasakthivel
263Enhancement of Mechanical Properties in Carbon Fibre Reinforced Epoxy Composite with and without graphite powderInternational Journal of Innovative Technology and Exploring EngineeringInternationalVol.8, No.12
pp.108-111
October 2019
D.Suresh
A.Sivakumar
264Design, Development and Analysis of Mullite catalytic convertor for CI engineSAE International International2019-28-0017
Published: October 2019
P.Selvakumar
S.Dhamotharan
A.Tamilvanan
N.Sathishkumar
265Development of sol-gel derived gahnite anti-reflection coating for augmenting the power conversion efficiency of polycrystalline silicon solar cellsMaterials Science-PolandInternationalVol.37, No.3
pp.465-472
September 2019
V.K.Gobinath
P.Senthil Velmurugan
P.Manivasakan
S.Mohankumar
P.Prabhakaran
R.Rajasekar
266Implementation of Total Productive Maintenance for Overall Equipment Effectiveness Improvement in Machine ShopInternational Journal of Recent Technology and EngineeringInternationalVol.8, No.3
pp.7686-7691
September 2019
A.Sivakumar
D.Suresh
267Performance and emission test in CI engine using magnetic fuel conditioning with nano additivesInternational Journal of Recent Technology and Engineering InternationalVol.8, No.3
pp.7823
September 2019
P.Sathiamurthi
K.S.Karthi Vinith
A.Sivakumar
268A retrofit for controlling the brightness of an automotive headlight to reduce glare by using embedded C program on a PIC microcontrollerInternational Journal of Recent Technology and EngineeringInternationalVol.8, No.3
pp.4240
September 2019
S.Ajay
N.Prasanna
S.Rajmohan
B.Roshan
P.T.Saravanan
269Performance of P1 model in the prediction of static temperature and velocity magnitude of therminol D-12 in an evacuated tube solar collectorInternational Journal of Innovative Technology and Exploring EngineeringInternationalVol.8, No.11
pp.255
September 2019
P.Selvakumar
P.Somasundaram
A.Tamilvanan
R.Karthikeyan
T.Rajagopal
270Dynamic characteristics of twisted composite panelsInternational Journal of Recent Technology and EngineeringInternationalVol.8, No.3
pp.255
September 2019
V.Hariharan
G.Rajeshkumar
P.Thangavel
271Enhancing the static and dynamic mechanical behaviour of vinyl ester matrix using surface modified luffa fibersInternational Journal of Recent Technology and EngineeringInternationalVol.8, No.3
pp.5785-5789
September 2019
S.Ramakrishnan
T.P.Sathishkumar
272Implementation of Species-Transport Model in Numerical Simulation to Predict the Performance of Downdraft Gasifier with Biomass BlendsEnergy Research JournalInternationalVol.10
pp.36-47
2019
P.C.Murugan
G.Arun Prasad
S.Joseph Sekhar
273Experimental investigation on the effect of multilayer TiCN/TiAlN/WC-C coating on the tribological behaviour of tool inserts for machining applicationsInternational Journal of Materials Engineering InnovationInternationalVol.10, No.3
pp.86-202
August 2019
C.Moganapriya
R.Rajasekar
K.Ponappa
P.Sathish Kumar
Samir Kumar Pal
S.Mahalakshmi
V.K.Gobinath
274Effects of thrust force variation during the drilling of pure and chemically treated Kevlar based polymer compositesMaterials TestingInternationalVol.61, No.9
pp.907-913
August 2019
A.Mohan Kumar
R.Parameshwaran
V.Krishnaraj
R.Rajasekar
275Performance analysis of vapour compression refigration system with mechanical subcoolingInternational Journal of Innovative Technology and Exploring EngineeringInternationalVol.8, No.8
pp.255
June 2019
S.Panneerselvam
P.Thangavel
S.Kannaki
276Experimental study on effect of wick structures on thermal performance enhancement of cylindrical heat pipesJournal of Thermal Analysis and CalorimetryInternationalVol.36, No.1
pp.389-400
April 2019
G.Kumaresan
P.Vijayakumar
M.Ravikumar
R.Kamatchi
P.Selvakumar
277Limit load evaluation of inlet pigtail pipe bends with ovality under in-plane bendingMaterials TestingInternationalVol.61, No.3
pp.267-272
March 2019
P.Ramaswami
P.SenthilVelmurugan
C.Moganapriya
R.Rajasekar
278Tool condition monitoring in the milling process with vegetable based cutting fluids using vibration signaturesJournal Materials TestingInternationalVol.61, No.3
pp.282-288
March 2019
T.Mohanraj
S.Shankar
R.Rajasekar
R.Deivasigamani
P.M.Arunkumar
279The influence of fiber content and length on mechanical and water absorption properties of CalotropisGigantea fiber reinforced epoxy compositesJournal of Industrial TextilesInternationalVol.48, No.8
pp.1274-1290
March 2019
K.Velusamy
P.Navaneethakrishnan
G.Rajeshkumar
T.P.Sathishkumar
280Study of the effect of varying shapes of holes in energy absorption characteristics on aluminium circular windowed tubes under quasi-static loadingStructural Engineering and MechanicsInternationalVol.70, No.2
pp.153-168
February 2019
N.Baaskaran
K.Ponappa
S.Shankar
281Management of musculoskeletal shoulder and neck pain through ergonomic intervention: a pre-post design analysis in hand screen printing industry International Journal of Business, innovation and researchInternationalVol.8, No.3
pp.392-409
February 2019
S.Shankar
R.Naveenkumar
J.Karthick
282Wet corrosion behavior of copper exposed to recycled groundnut oil as biofuelMaterials TestingInternationalVol.61, No.2
pp.131-135
March 2019
S.V.Priya
G.Sangeetha
R.Saratha
V.K.Gobinath
P.Sathishkumar
R.Rajasekar
283Prediction of cutting tool wear during milling process using artificial intelligence techniquesInternational Journal of Computer Integrated ManufacturingInternationalVol.32. No.2
pp.174-182
February 2019
S.Shankar
T.Mohanraj
R.Rajasekar
284Experimental analysis on the technical behavior of carbon black filled rubber blends' rollers for rice husk removal applicationPolimeryInternationalVol.64, No.1

pp.50-55
January 2019
P.Prabhakaran
R.Rajesh
R.Rajasekar
V.K.Gobinath
P.Sathish Kumar
S.K.Pal
C.Moganapriya
285Influence of Coating Material and Cutting Parameters on Surface Roughness and Material Removal Rate in Turning Process Using Taguchi MethodMaterials Today: ProceedingsInternationalVol.5, No.2
pp.8532-8538
December 2018
C.Moganapriya
R.Rajasekar
K.Ponappa
R.Venkatesh
S.Jerome
286Mechanical and tribological behavior of SiC and fly ash reinforced Al 7075 composites compared to SAE 65 bronze Materials TestingInternationalVol.60, No.12
pp.1225-1231
December 2018
V.Gobinath
P.Sathish Kumar
S.Mohan Kumar
R.Deivasigamani
R.Rajasekar
287Effect of coating on tool inserts and cutting fluid flow rate on the machining performance of AISI 1015 steelMaterials TestingInternationalVol.60, No.12
pp.1202-1208
December 2018
C.Moganapriya
R.Rajasekar
K.Ponappa
P.Sathish Kumar
Samir Kumar Pal
J.Saravana Kumar
288Assessment of dynamic crushing and energy absorption characteristics of thin-walled cylinders due to axial and oblique impact loadSteel and Composite structures InternationalVol.28, No.2
pp.179-194
July 2018
N.Baaskaran
K.Ponappa
S.Shankar
289Synergy of cashew nut shell filler on tribological behaviors of natural-fiber-reinforced epoxy compositeScience and Engineering of Composite MaterialsInternationalVol.25, No.4
pp.761-772
July 2018
T.P.Sathishkumar
S.Arun Kumar
P.Navaneethakrishnan
I.Siva
N.Rajini
290Fabrication and characterisation of nanofibrous polyurethane scaffold incorporated with corn and neem oil using single stage electrospinning technique for bone tissue engineering applicationsJournal of Polymer ResearchInternationalVol.25, No.7
pp.146
July 2018
Saravana Kumar Jaganathan
Mohan Prasath Mani
Sathish Kumar Palaniappan
Rajasekar Rathanasamy
291Preparation, characterization and blood compatibility assessment of a novel electrospun nanocomposite comprising polyurethane and ayurvedic-indhulekha oil for tissue engineering applicationsBiomedical Engineering/Biomedizinische TechnikInternationalVol.63, No.3
pp.245-253
June 2018
Manikandan Ayyar
Mohan Prasath Mani
Saravana Kumar Jaganathan
Rajasekar Rathanasamy
292Influence of Coating Material and Cutting Parameters on Surface Roughness and Material Removal Rate in Turning Process Using Taguchi MethodMaterials Today: ProceedingsInternationalVol.5, No.2
pp.8532-8538
2018
C.Moganapriya
R.Rajasekar
K.Ponappa
R.Venkatesh
S.Jerome
293A study on heat transfer characteristics of inclined copper sintered wick heat pipe using surfactant free CuO and Al2O3 nanofluidsJournal of the Taiwan Institute of Chemical EngineersInternationalVol.81
pp.190-198
December2017
M.Vijayakumar
P.Navaneethakrishnan
G.Kumaresan
R.Kamatchi
294Partial replacement of carbon black by nanoclay in butyl rubber compounds for tubeless tiresMaterials TestingInternationalVol.59, No.11-12
pp.1054-1060
November 2017
M.Harikrishna Kumar
S.Shankar
R.Rajasekar
Pal Samir Kumar
P.Sathish Kumar
295Folic acid decorated chitosan nanoparticles and its derivatives for the delivery of drugs and genes to cancer cellsCurrent ScienceInternationalVol.113, No.8
pp.1-13
October 2017
Agnes Aruna John
S.Jaganathan
A.Manikandan Navaneetha Pandiyaraj Krishnasamy
R.Rajasekar
Eko Supriyanto
296Analysis of Solid Contamination in Ball Bearing Through Acoustic Emission SignalsArchives of Metallurgy and MaterialsInternationalVol.62, No.3
pp.1871-1874
September 2017
K.A.Ibrahim Sheriff
V.Hariharan
T.Kannan
297Optimization of Constrained Layer Damping Parameters in Beam Using Taguchi MethodIranian Journal of Science and Technology, Transactions of Mechanical EngineeringInternationalVol.41, No.3
pp.243-250
September 2017
K.S.K.Sasikumar
K.P.Arulshri
S.Selvakumar
298Experimental analysis of nitrogen as an alloying element in wc9 grade steelArchives of Metallurgy and MaterialsInternationalVol.62, No.3
pp.1889-1894
September 2017
R.Rajasekar
V.Vishnuh
S.Sudhakar
K.Tamilarasu
P.Prabhakaran
299Effect of ovality in inlet pigtail pipe bends under combined internal pressure and in-plane bending for ni-fe-cr b407 materialArchives of Metallurgy and MaterialsInternationalVol.62, No.3
pp.1881-1887
September 2017
R.Rajasekar
P.Ramaswami
P.Senthil Velmurugan
300Review on parameters influencing the rice breakage and rubber roll wear in shellerArchives of Metallurgy and MaterialsInternationalVol.62, No.3
pp.1875-1880
September 2017
S.K.Pal
P.Prabhakaran
R.Ranganathan
V.Muthu kumar
R.Rajasekar
L.Devakumar
301Dry sliding wear and mechanical characterization of mg based composites by uniaxial cold press techniqueArchives of Metallurgy and MaterialsInternationalVol.62, No.3
pp.1851-1856
September 2017
B.Aravindkumar
P.Selvakumar
K.Ponappa
M.Udhayasankar
302Characterization of case hardened aisi 4130 steel using eddy current testingArchives of Metallurgy and MaterialsInternationalVol.62, No.3
pp.1833-1837
September 2017
K.Ponappa
R.Gukendran
R.Parameshwaran
303Influence of cutting fluid flow rate and cutting parameters on the surface roughness and flank wear of tialn coated tool in t...Archives of Metallurgy and MaterialsInternationalVol.62, No.3
pp.1827-1832
September 2017
C.Moganapriya
R.Rajasekar
K.Ponappa
R.Venkatesh
R.Karthick
304Influence of rock properties on wear of m and sr grade rubber with varying normal load and sliding speedArchives of Metallurgy and MaterialsInternationalVol.62, No.3
pp.1787-1793
September 2017
R.Rajasekar
Samir Kumar Pal
K.U.M.Rao
P.Sathish Kumar
305Formation of functional nanofibrouselectrospun polyurethane and murivenna oil with improved haemocompatibility for wound healingPolymer TestingInternationalVol.61
pp.106–113
August 2017
A.Manikandan
M.M.Prasath
S.K.Jaganathan
R.Rajasekar
M.Jagannath
306Tribomechanical behavior of TiCN/TiAlN/WC-C multilayer ?lm on cutting tool inserts for machiningMaterials TestingInternationalVol.59, No.7-8
pp.703-707
July 2017
C.Moganapriya
R.Rajasekar
K.Ponappa
R.Karthick
R.Venkatesh
307Quasi-Static Crushing and Energy Absorption Characteristics of Thin-Walled Cylinders with Geometric Discontinuities of Various Aspect RatiosLatin American Journal of Solids and StructuresInternationalVol.14, No.9
pp.1767-1787
July 2017
N.Baaskaran
K.Ponappa
S.Shankar
308Effects of abaca fiber reinforcement on the dynamic mechanical behavior of vinyl ester compositesMaterials TestingInternationalVol.59, No.6
pp.555-562
June 2017
A.Mohan Kumar
R.Parameshwaran
P.Sathish Kumar
S.K.Pal
M.M.Prasath
V.Krishnaraj
R.Rajasekar
309Development of calcium titanium oxide coated silicon solar cells for enhanced voltage generation capacityMaterials Science-PolandInternationalVol.35, Vol.1
pp.181-187
April 2017
K.Kathirvel
R.Rajasekar
T.Shanmuharajan
SK.Pal
P.Sathish Kumar
310Influence of vegetable based cutting fluids on cutting force and vibration signature during milling of aluminium metal matrix compositesJournal Tribologi InternationalVol.12, No.1
pp.1-17
March 2017
S.Shankar
T.Mohanraj
K.Ponappa
311Tribomechanical behavior of B4Cp reinforced Al 359 compositesMaterials Testing InternationalVol.59, No.2
pp.172-177
February 2017
D.Ramasamy
MK.Subramanian
GV.Kaliyannan
J.Durairaj
R.Rajasekar
312Mechanical and Corrosion Behavior of Al7075 (Hybrid) Metal Matrix Composites by Two Step Stir Casting ProcessLatin American Journal of Solids and StructuresInternationalVol.14, No.2
pp.243-255
February 2017
M.Sambathkumar
P.Navaneethakrishnan
K.Ponappa
KSK.Sasikumar
313Experimental and Mathematical Investigation on Performance and Emission Characteristics of Ethanol Fumigation in a Single Cylinder Diesel EngineAsian Journal of Research in Social Sciences and Humanities InternationalVol.7, No.1
pp.632-652
January 2017
M.Bharathiraja
Venkatachalam
N.Prasanna
314Experimental and mathematical investigation on performance and emission characteristics of oxygen enriched air in intake of a single cylinder diesel engineJournal of Advance in ChemistryInternationalVol.12, No.27
pp.5814-5824
January 2017
V.SenthilMurugan
R.Venkatachalam
M.Bharathiraja
315Characterization of Phoenix sp. natural fiber as potential reinforcement of polymer compositesJournal of Industrial TextilesInternationalVol.46, No.3
pp.667-683
December 2016
G.Rajeshkumar
V.Hariharan
T.P.Sathishkumar
316Thermal characteristics studies on sintered wick heat pipe using CuO and Al2O3 nanofluidsExperimental Thermal and Fluid ScienceInternationalVol.79
pp.25-35
December 2016
M.Vijayakumar
P.Navaneethakrishnan
G.Kumaresan
317Effect of NaOH Treatment on Properties of Phoenix Sp. FiberJournal of Natural FibersInternationalVol.13, No.6
pp.702-713
November 2016
G.Rajeshkumar
V.Hariharan
T.Scalici
318Acoustic emission testing of the machining performance of SiC grinding wheel shaped Al2O3 ceramicsMaterials TestingInternationalVol.58, No.10
pp.908912
October 2016
P.Kanakarajan
S.Sundaram
A.Kumaravel
R.Rajasekar
R.Venkatachalam
319Fabrication and hemocompatibility assessment of novel polyurethane-based bio-nanofibrous dressing loaded with honey and Carica papaya extract for the management of burn injuriesInternational Journal of NanomedicineInternationalVol.11, pp.4339-4335
September 2016
A.Balaji
J.Saravana Kumar
Ahmad Fauzi Ismail
R.Rajasekar
320Experimental investigation of planted pin fin in plate fin heat sink electronics coolingJournal of Heat and Mass TransferInternationalVol.13, No.2
pp.143-160
July 2016
M.Vijyakumar
P.Navaneethakrishnan
R. Mohan
321Effect of Pretreatment Methods on Properties of Natural Fiber Composites: A Review Polymers & Polymer Composites InternationalVol.24, No.7
pp.555-566
June 2016
N.Venkatachalam
P.Navaneethakrishnan
R.Rajasekar
S.Shankar
322Analysis of Al7075 hybrid metal matrix composite using Two dimensional microstructure model based finite Element method International Journal of Advanced Engineering TechnologyInternationalVol.7, No.2
pp.180-183
June 2016
M.Sambathkumar
P.Navaneethakrishnan
K.Ponappa
K.S.K.Sasikumar
P.Arunkumar
323Experimental Analysis on Solar Water Heater with Corrugated Absorber for Enhanced Heat TransferJournal of Thermal Energy SystemsInternationalVol.1, No.2
pp.819
June 2016
P.Selvakumar
P.Somasundaram
324Machining Fixture Layout Optimization For Machining Of Brake DrumVSRD International Journal of Mechanical, Civil, Automobile and Production EngineeringInternationalVol.4, No.2
February 2016
S. Selvakumar
325Optimal Fixture Design for Drilling of Elastomer using DOE and FEMJournal of Advances in Mechanical Engineering and ScienceInternationalVol.2, No.2
pp.1-19
March 2016
S.Selvakumar
K.M.Arunraja
P.Praveen
326Development of snake grass fiber-reinforced polymer composite chairJournal of Materials: Design and ApplicationsInternationalVol.230, No.1
pp.273-281
January 2016
T. P.Sathishkumar
327Dynamic mechanical analysis of snake grass fiber-reinforced polyester compositesJournal of Materials: Design and ApplicationsInternationalVol.230, No.1
pp.106-174
January 2016
T. P. Sathishkumar
328Impact of Nano Medicines in Human LifeInternational Journal of Engineering and Management ResearchInternationalVol.5, No.4
pp.91-95
August 2015
A.Abubakkar
329Acoustic emission testing of surface roughness and wear caused by grinding of ceramic materialsMaterials Testing InternationalVol.57, No.4
pp. 1-6
April 2015
P.Kanakarajan
S.Sundaram
A.Kumaravel
R.Rajasekar
P.Sathish Kumar
330Theoretical Prediction on the Mechanical Behavior of Natural Fiber Reinforced Vinyl Ester CompositesApplied Science and Advanced Materials InternationalVol.1, No.3
pp.85-92
January 2015
S.Ramakrishnan
K.Krishnamurthy
R.Sarathkumar
R.Rajasekar
331Free vibration characteristics of phoenix Sp fiber reinforced polymer matrix composite beamsProcedia EngineeringInternationalVol.97, pp.687-693
December 2014
G.Rajeshkumar
V.Hariharan
332Comparison of Sansevieriaehrenbergii fiber-reinforced polymer composites with wood and wood fiber compositesJournal of Reinforced Plastics and CompositesInternationalVol.33, No.18
pp.1704-1716
September 2014
T.P.Sathishkumar
333Mechanical properties and water absorption of short snake grass fiber reinforced isophthallic polyester compositesFibers and PolymersInternationalVol.15, No.9
pp.1927-1934
September 2014
T.P.Sathishkumar
P.Navaneethakrishnan
S.Shankar
R.Rajasekar
334Comparitive investigation of mechanical properties in GMAW and GTAW for various shielding gas compositionJournal of materials and manufacturing processesInternationalVol. 29, No.8
pp.996-1003
July 2014
K.V.Satheeshkumar
S.Gejendhiran
M.Prasath
335Effect of layered double hydroxide in polymer nanocomposites the reviewNanotrendsInternationalVol.16, No.2
pp.1-18
August 2014
PonMaheskumar
P.Sathish Kumar,
P.Sathiamurthi
R.Rajasekar
336Characterization of Phoenix fiber and its Composites International Journal of ChemTech ResearchInternationalVol.6, No.3
pp.1887-1889
May-June 2014
G.Rajesh Kumar
P.Janarthanan
V.Hariharan
337Study on Wear and Friction Characteristics of Brake Rotor made of A359- B4CP Composites International Journal of ChemTech ResearchInternationalVol.6, No.3
pp.1684-1686
May-June 2014
S.Mohankumar
R.Deivasigamani
338Effect of Mechanical behaviours of Graphene oxide reinforced compatibilized High density PolyethyleneInternational Journal of ChemTech ResearchInternationalVol.6, No.3
pp.1894-1897
May-June 2014
K.V.Mahesh Kumar
K.Krishnamurthy
P.Sathish Kumar
R.Rajasekar
A.Siva kumar
339Electrostatically assembled layer-by-layer composites containing graphene oxide for enhanced hydrogen gas barrier applicationComposites Science and TechnologyInternational Vol.89, pp.167-174
December 2013
Rathanasamy Rajasekar
Nam Hoon Kim
Daeseung Jung
Tapas Kuila
Jae Kyoo Lim
Min Jeong Park
Joong Hee Lee
340Effects of evaporator load on vapour compression refrigeration system using eco-friendly hydrocarbon refrigerants with sub-cooling Journal of Scientific and Industrial ResearchInternational Vol.72, pp.695-702
Nov 2013
P.Thangavel
P.Somasundaram
341Design and fabrication of staircase climbing wheelInternational Journal of Mechanical Engineering and Robotics ResearchInternational Vol.2, No.2
pp.320-323, 2013
R.Rajasekar
K.P.Pranavkarthik
R.Prashanth
S.Senthilkumar
A.Sivakumar
342Optimization of mechanical properties of non-woven short siscal fibre-reinforced vinyl ester composite using factorial design and GA methodBulletin of Materials ScienceInternational Vol.36, No.4
pp.575-583, 2013
P.Navaneethakrishnan
S.Velumani
343Mechanical and Machinability Behaviours of Woven Coir Fiber-Reinforced Polyester CompositeFibers and CompositesInternational Vol.14, No.9
pp.1505-1514, 2013
P.Navaneethakrishnan
S.Velumani
344Performance improvement and cost minimisation for manufacturing components in a fabrication plant by the application of lean with TRIZ principlesInternational Journal for Productivity and Quality ManagementInternational Vol.12, No.4
pp.449-465, 2013
P.Navaneethakrishnan
R.Muruganandam
345Design and optimization of machining fixture layout using ANN and DOEJournal of Advanced Manufacturing TechnologyInternational Vol.65, No.9-12
pp.1573-1586, 2013
S.Selvakumar
K.P.Arulshri
K.Padmanaban
KSK.Sasikumar
346Machining fixture layout optimization using genetic algorithm and artificial neural networkInternational Journal of Manufacturing ResearchInternational Vol.8, No.2
pp.171-195, 2013
S.Selvakumar
K.P.Arulshri
K.Padmanaban
347Instant hot water generation system for domestic utility in rural areasInternational Review of Mechanical EngineeringInternational Vol.7, No.5
pp.869-873, 2013
P.Selva Kumar
P.Somasundaram
348Effective heat transfer enhancement in finned tube heat exchanger with different fin profilesInternational Journal of Engineering ResearchInternational Vol.2, No.2
pp.83-87, 2013
J.A.Livingston
P.Selva Kumar
349Simulation Analysis of Compression Refrigeration Cycle with Different RefrigerantsInternational Journal of Engineering and Innovative TechnologyInternational Vol.2, No.10
pp.127-131, 2013
P.Thangavel
P.Somasundaram
T.Sivakumar
C.SelvaKumar
G.Vetriselvan
350Simulation analysis on thermo physical properties of hydrocarbon refrigerants in vapour compression refrigeration systemInternational Review of Mechanical EngineeringInternational Vol.4, No.7
pp.646-651, 2013
P.Thangavel
P.Somasundaram
P.Navaneethakrishnan
351Characterization of natural fiber and composites - a reviewJournal of Reinforced Plastics and CompositesInternational Vol.32, No.16
pp.1446-1465, 2013
T.P.Sathishkumar
P.Navaneethakrishnan
S.Shankar
R.Rajasekar
352Characterization of new cellulose sansevieria ehrenbergii fibers for polymer compositesComposite InterfacesInternational Vol.20, No.8
pp.575-593, 2013
T.P.Sathishkumar
P.Navaneethakrishnan
S.Shankar
R.Rajasekar
353Influence of chemically treated longitudinal oriented snake grass fiber reinforced isophthallic polyester composites.Journal of Reinforced Plastics and CompositesInternational Vol.32, No.22
pp.1698-1714, 2013
T.P.Sathishkumar
P.Navaneethakrishnan
S.Shankar
R.Rajasekar
354Hybrid fiber reinforced polymer composites-A review Journal of Reinforced Plastics and CompositesInternational DOI: 10.1177/
0731684413516393
2013
T.P.Sathishkumar
J.Naveen
S.Satheeshkumar
355Mechanical properties and water absorption of snake grass longitudinal fiber reinforced isophthallic polyester compositesJournal of Reinforced Plastics and CompositesInternationalVol. 32, No.16
pp.1211-1223, 2013
T.P.Sathishkumar
S.Shankar
P.Navaneethakrishnan
R.Rajasekar
356Tools and models used for productivity improvement in Manufacturing, Chemical and Chemical Allied industries: A literature reviewInternational Journal of Management Research and ReviewInternational Vol.2, No.2
pp.293-307, 2012
A.Sivakumar
K.Saravanan
357Statistical Approach of Fault Identification and Classification of Bearings Condition Using ArtificialInternational Journal of Mechanic Systems EngineeringInternational Vol.2, No.4
pp.154-168, 2012
V.Hariharan
PSS.Srinivasan
358Classification of rolling element bearing fault using artificial neural networkElixir Journal of Mechanical EngineeringInternational Vol.49, pp.9964-9968
2012
V.Hariharan
PSS.Srinivasan
359Mechanical properties of randomly oriented snake grass fiber with banana and coir fiber reinforced hybrid compositesJournal of Composite MaterialsInternational Vol.47, No.18
pp.2181-2191, 2012
T. P.Sathishkumar
P.Navaneethakrishnan
S.Shankar
J.Kumar
360Experimental investigation of randomly oriented natural fiber hybrid compositesNational Journal of technologyNationalVol.8, No.2
pp.74-79, 2012
T.P.Sathishkumar
L.Rajesh kumar
P.Navaneethakrishnan
361Globalisation effect of productivity and quality dimensions on capacity utilization through multivariate confirmatory analysisEnterprise Network ManagementInternationalVol.5, No.4
pp.355-380, 2012
A.Sivakumar
K.Saravanan
P.Navaneethakrishnan
R.Rajasekar
362Mathematical approach for optimal machining fi xture layout and clamping forces Australian Journal of Mechanical EngineeringInternationalVol.10, No.1
pp.17-28, 2012
S.Selvakumar
K.P.Arul Shri
K.P.Padmanaban
K.S.K.Sasikumar
363Effect of Inclination angle on temperature characteristics of water-in-glass evacuated tubes of domestic solar water heaterEngineering and Innovative TechnologiesInternationalVol.1, No.4
pp.78-81, April 2012
P.Selvakumar
364Tensile and flexural properties of snake grass natural fiber reinforced isophthallic polyester composites Composites Science and TechnologyInternationalVol.72, pp.1183-1190
April 2012
T.P.Sathishkumar P.Navaneethakrishnana S.Shankar
365Improvement of productivity through total productive maintenance in Textile IndustryJournal of Industrial EngineeringNationalVol.3, No.1, 2012A.Sivakumar
P.Navaneethakrishnan
K.Saravanan
366Neural network prediction of flow stress of cast AL-5si Alloy under Hot CompressionEuropean Journal of Scientific Research (EJSR)InternationalVol.68, No.2
2012
R.Deivasigamani
V.P.Arunachalam
367Study of mechanical behavior of sandwich composite materialsInternational Journal of applied Engineering ResearchInternational Vol.6, No.5
pp.831-840, 2011
N.Venkatachalam
R.Deivasigamani
368A Simulation based analysis for improvement of Productivity in Sick Chemical Dyeing Factory : A Research ArticleInternational Journal of Electronic transportInternational Vol.1, No.1
pp.96-110, 2011
A.Sivakumar
K.Saravanan
369Design and Development of waste heat recovery system for air conditioning unitEuropean Journal of Scientific Research (EJSR)InternationalVol.54, No.1
pp.102-110, 2011
P.Sathiamurthi
P.S.S.Srinivasan
370Numerical and experimental study of the effect of constraining layer in controlling the vibration of beams attached with PCLDBulletin of Applied MechanicsInternationalVol.7, No.25
pp.1-7, 2011
K.S.K.Sasikumar
K.P.Arulshri
S.Selvakumar
N.S.Nandhakumar
371An analysis of the effect of constraining layer modulus on the Vibration control of beams treated with PCLDEuropean Journal of Scientific Research (EJSR)InternationalVol.66, No.3
2011
K.S.K.Sasikumar
S.Selvakumar
K.P.Arulshri
372A Systemized operational Planning, implementation and Analysis of Robust Framework for improvement of partial and total productivity in Textile Fabric industry : A Research paperEuropean Journal of Scientific Research (EJSR)InternationalVol.53, No.3
pp.385-399, 2011
A.Sivakumar
P.Navaneethakrishnan
K.Saravanan
373Productivity and production analysis in fabric manufacturing industry-A Robust design frame workPublished in Digital LibraryInternational11-DecA.Sivakumar
P.Navaneethakrishnan
K.Saravanan
374Vibration analysis of parallel misaligned shaft with ball bearing systemSongklanakarin Journal of Science and TechnolologyInternationalVol.33, No.1
pp.61-68, 2011
V.Hariharan
P.S.S.Srinivasan
375Simulation of recharging battery of the pacemaker using piezoelectric crystal from the pulse in aortaInternational Journal of Mechanical and production Engineering and research and developmentInternationalVol.1, No.2, 2011T.Gopinathan
K.P.Arulshri
376Clamping Force Optimization for Minimum Deformation of Workpiece by Dynamic Analysis of Workpiece-fixture SystemWorld Applied Sciences Journal InternationalVol.11, No.7
pp.840-846, 2010
S.Selvakumar
K.P.Arulshri
K.P.Padmanaban
K.S.K.Sasikumar
377Application of ANN in the Machining Fixture Layout Optimization for Minimum Deformation of Work piece using FEMInternational Journal of Applied Engineering Research InternationalVol.5, No.10
pp.1801-1820, 2010
S.Selvakumar
K.P.Arulshri
K.P.Padmanaban
378Design and Implementation of Robust Framework for Improvement of Productivity through Total Productive Maintenance in Textile IndustryInternational Journal of Decision making in Supply Chain And logistics - IJDMSCLInternationalVol.1, No.2
pp.167-177, 2010
A.Sivakumar
K.Saravanan
379Some Studies on the Effect of Constraining Layer in the Vibration Control of Beams using PCLDInternational Journal of Applied Engineering ResearchInternationalVol.5, No.15
pp.2545-2556, 2010
K.S.K.Sasikumar
K.P.Arulshri
S.Selvakumar
380investigations of the effect of parameters of constraining layer in controlling the vibration of beams attached with PCLDInternational Journal of Engineering Research & Industrial ApplicationsInternationalVol.3, No.4
pp.307-320, 2010
K.S.K.Sasikumar
K.P.Arulshri
S.Selvakumar
381Design optimization of dosa making workstation for smooth ergonomic interfaceJournal of Scientific & Industrial ResearchInternationalVol.69, pp.221-224
2010
A.Somasundaram
P.S.S.Srinivasan
382Risk assessment and Ergonomic Analysis for the design of Kitchen workstation used in Indian Middle-Class HotelsThe IUP Journal of Mechanical EngineeringInternationalVol.3, No.4
pp.61-68, 2010
A.Somasundaram
P.S.S.Srinivasan
383Vibration Analysis of Flexible Coupling by Considering UnbalanceWorld Applied Sciences Journal InternationalVol.8, No.8
pp.1022-1031, 2010
V.Hariharan
P.S.S.Srinivasan
384Condition monitoring studies on ball bearings considering solid contaminants in the lubricantJournal of Mechanical Engineering ScienceInternationalVol.224, No.8
pp.1727-1748, 2010
V.Hariharan
P.S.S.Srinivasan
385Vibration Analysis of Flexible Coupling by Considering UnbalanceMiddle East Journal of Scientific Research InternationalVol.5, No.5
pp.336-345, 2010
V.Hariharan
P.S.S.Srinivasan
386Numerical and Experimental Investigation of temperature distribution inside the heating ovenJournal of food processing and PreservationInternationalVol.32, pp.257-269
2009
P.Navaneetha
Krishnan
P.S.S.Srinivasan
S.Dhandapani
387Effect of Flow Guide in Commercial Shop Display CabinetInstitution of Engineers (India) JournalNationalVol.89, pp.18-22
2009
P.Navaneethakrishnan
P.S.S.Srinivasan
S.Dhandapani
388Dynamic Balancing of a CNC Machine Spindle Using Vibration Signature: A Case Study of Turning Center on Condition MonitoringICFAI University Journal of Mechanical EngineeringInternationalVol.2, No.2
pp.20-27, 2009
V.Hariharan
P.S.S.Srinivasan
389Vibration analysis of antifriction bearing to detect outer race defect International Journal of Engineering Research and Industrial Applications InternationalVol.2, No.1
pp.139-148, 2009
V.Hariharan
P.S.S.Srinivasan
390Experimental Investigation on bearing housing vibration signatures caused by shaft rub Journal of Mechanical EngineeringInternationalVol.60, No.2
pp.61-74, 2009
V.Hariharan
P.S.S.Srinivasan
391Vibration analysis of misaligned Ball bearing systemIndian Journal of Science and TechnologyNationalVol.2, No.9
pp.45-50, 2009
V.Hariharan
P.S.S.Srinivasan
392New approach of classification of rolling element bearing fault using Artificial Neural NetworkJournal of Mechanical Engineering, Transaction of the Mech. Eng. Div., The Institution of Engineers, BangladeshInternationalVol.40, No.2
pp.119-120, 2009
V.Hariharan
P.S.S.Srinivasan
393Machining fixture layout design using ant colony algorithm based continuous optimization methodInternational Journal of Advanced Manufacturing TechnologiesInternationalVol.45, No.2
pp.922-934, 2009
K.P.Arulshri
K.P.Padmanaban
G.Prabhakaran
394Eigen value analysis of orthotropic laminated plates using higher order shear deformation theoryICFAI University Journal of Mechanical EngineeringInternationalVol.1, No.2
pp.59-78, 2008
V.Hariharan
P.S.S.Srinivasan
395A simple prediction method for laminar film-condensation over horizontal intergral-fin copper tubesJournal of Energy, Heat & Mass transferInternationalVol.30, pp.311-322
2008
E.Vallinayagam
396Constitutive modeling of Shape Memory Alloy Using Artificial neural networkJournal of Manufacturing EngineeringInternationalVol.9,pp.61-65, 2008K.P.Arulshri
K.P.Padmanaban
V.Selladurai
397Analysis of Heat transfer enhancement in Spiral plate heat exchangerInternational Journal of Modern Applied Science InternationalVol.2 No.4
pp.68-75, 2008
R.Rajavel
K.Saravanan
398An experimental study of spiral plate Heat exchanger for electrolytesJournal of the University of Chemical Technology and MetallurgyInternationalVol.43, No.4
pp.255-260, 2008
R.Rajavel
K.Saravanan
399An Experimental Investigation of heat transfer Coefficients for Spiral plate heat exchangerInternational Journal of Modern Applied Science InternationalVol.2, No.5
pp.14-20, 2008
R.Rajavel
K.Saravanan
400Heat transfer studies on Spiral plate heat exchangerInternational Journal of Thermal ScienceInternationalVol.12, No.3
pp.85-90, 2008
R.Rajavel
K.Saravanan
401Performance and Emission achievements by magnetic energizer with a single cylinder two stroke catalytic coated spark ignition engineJournal of Science and Industrial ResearchInternationalVol.66, pp.457-463
2007
P.Govindasamy
S.Dhandapani
402Experimental Investigation of cyclic variation of combustion parameters in catalytically activated and magnetically energized two-stroke SI engineInternational Journal of Energy & Environment InternationalVol.6, pp.45-60, 2007 P.Govindasamy
S.Dhandapani
403A Tabu Search Algorithm for Job shop Scheduling problem with Industrial Scheduling Case studyInternational Journal of soft computingInternationalVol.2, No.4
pp.531-537, 2007
P.Senthil Velmurugan
V.Selladurai
404Design and development of modified service failure mode and effects analysis modelInternational Journal of Services and Operations ManagementInternationalVol.3, No.1
pp.111-126, 2007
C.Jegadheesan
V.P.Arunachalam
S.R.Devadasan
P.S.S.Srinivasan
405Computer Simulation of Bio-Medical Stent Using Finite Element MethodACCST Research Journal InternationalVol.4, No.1
pp.46-52, 2006
S.P.Arul
V.Selladurai